參數資料
型號： P95020ZNQGI8
廠商： INTEGRATED DEVICE TECHNOLOGY INC
元件分類： 電源管理
英文描述： 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC132
封裝： QFN-132
文件頁數： 137/137頁
文件大?。?/td> 3533K
代理商： P95020ZNQGI8
P95020 / Preliminary Datasheet
Revision 0.7.10
99
2010 Integrated Device Technology, Inc.
TSC
– MEASURING TOUCH SCREEN PRESSURE (Z1/Z2)
The user can configure whether pressure measurements will be taken by writing to the Pressure Measure Control bits in
the TSC Configuration Register. When measuring touch screen pressure, two parameters (Z1 and Z2) are measured
automatically. Along with the X/Y measurement, these values can be used to calculate the touch-resistance (RTOUCH) with
a formula such as:
1
2
4096
Z
X
R
PLATE
X
TOUCH
Where RX-PLATE is the X-plate panel resistance.
ADC
Y+
Y-
X-
X+
GND
REF-
REF+
VDD
R-touch
ADC
Y+
Y-
X-
X+
GND
REF-
REF+
VDD
R-touch
Measure Z1-Position
Measure Z2-Position
12.3.2
GENERAL PURPOSE ADC MODE
In this mode, GPIO6/7/8/9 are analog general purpose auxiliary signal inputs ADC1/ADC3/ADC2/ADC0. There are also
other four internal signals connect to ADC input multiplexer: BAT, TEMP, VSYS and ICHRG. Those signals are for battery
voltage, die temperature, system voltage and charging current measurement.
ADC AUTO POWER DOWN MODE
In this mode, the ADC and internal reference is usually off. When a measurement is either scheduled by internal timer or
external request, the device powers up the ADC and internal reference, and waits for the internal reference to settle. Then
the signal acquisition starts. The ADC and the reference will be powered down after all the outstanding
scheduled/requested tasks are finished. All the measurement channels will be served in a round robin manner.
ADC ALWAYS ON MODE
In this mode, the ADC is always powered up and the internal ADC reference is always on. The internal reference remains
fully powered after completing a sequence. All the measurement channels will be served in a round robin manner.
12.3.3
SYSTEM MONITORING AND ALERT GENERATION
There are four internal channels support scheduled measurement and monitoring:
Battery voltage (VBAT) measurement
Die Temperature (VTEMP) measurement
Vsys Level (VSYS) measurement
Battery charging current (CHRG_ICHRG) measurement
Among those, three of them are with alert signal generation:
Battery voltage
Die temperature
Vsys level
Measured results are saved in dedicated result registers and compared with pre-defined spec limits. If it is out of the limit,
an alert (map to processor interrupt) signal can be asserted and alert status will be set.
相關PDF資料
PDF描述
P95020ZLLG 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA124
P95020ZLLGI 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA124
P95020ZNQGI 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC132
P95020ZNQG 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC132
P95020ZLLG8 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA124
相關代理商/技術參數
參數描述
P95021NQG 功能描述:PMIC 解決方案 Integrates Audio, LED B/Light Pwr Mgt RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
P95021NQG8 制造商:Integrated Device Technology Inc 功能描述:POWER MANAGEMENT, AUDIO & CONT 制造商:Integrated Device Technology Inc 功能描述:132-VFQFPN - Tape and Reel 制造商:Integrated Device Technology Inc 功能描述:Integrates Audio, LED B/Light Pwr Mgt
P950-36I 制造商:Tripp Lite 功能描述:SERIAL ATA II SIGNAL CABLE, 2X7-PIN STRAIGHT CONNECTOR - 39" - Bulk
P9508- 制造商:ROEBUCK 功能描述:ROEBUCK DISH WASHING BRUSH
P9-511121 功能描述:按鈕開關 Flush Dome Solder 5A SPST-DB, SPDT-DB RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 安裝風格: 照明: 照明顏色: IP 等級: 端接類型: 觸點電鍍: 執行器: 蓋顏色: 封裝: 可燃性等級:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*