參數資料
型號： P95020ZLLGI8
廠商： INTEGRATED DEVICE TECHNOLOGY INC
元件分類： 電源管理
英文描述： 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA124
封裝： LLGA-124
文件頁數： 11/137頁
文件大?。?/td> 3533K
代理商： P95020ZLLGI8
P95020 / Preliminary Datasheet
Revision 0.7.10
108
2010 Integrated Device Technology, Inc.
The firmware (boot sequence) starts with checking whether the external ROM is available (read EX_ROM bit in
the global registers). If it exists, load the EX_ROM data into internal RAM. Other wise, execute code in the
internal ROM.
Firmware execute the code according the context and interrupt to sequence the power.
After the sequence is done, processor enter low power mode and wait for interrupts.
13.4 POWER ON RESET OUTPUT (POR_OUT)
The POR_OUT pin is an open drain GPIO output pin which controlled by firmware as part of the power up sequence. This
signal is used to reset the devices in the system that are powered by P95020 device while the power is not yet ready. The
output state of POR_OUT is defined by the power up sequence.
13.5 POWER SWITCH DETECTOR (SW_DET)
The PCON module also includes special power switch detection
circuitry to provide a “push-on/push-off” interface via the
switch detect (SW_DET) pin. By connecting a button to this pin, three different events can be triggered. The first is a
short switch interrupt (>100ms) which is generated by momentarily pressing and releasing a button attached to SW_DET.
The second is a medium switch interrupt which is generated by pressing and holding the button and releasing it after 2
seconds (configurable to 2/3/4/5 seconds). The status of each of these switches can be monitored in the Switch Control
Register (0xA031). The third switch function is triggered when the button is pressed and held for longer than 15 seconds.
This event will not generate an interrupt but will generate system reset and force P95020 into OFF state.
13.6 GPIO GENERAL DESCRIPTION
The GPIO pins are turned on and off using the GPIO Off Register. This register is used like a multiplexer to allow the
GPIO and TSC/ADC subsystems to share external pins. W
hen in GPIO mode (GPIO_OFF bits set to logic 0) the GPIO
Function Register configures the pin to operate as a GPIO or some other special function such as a status LED output. If
not configured to perform a special function, each GPIO can be configured as an input or output by setting the
corresponding bit in the GPIO Direction Register.
When configured as an output, each GPIO pin can be configured as a CMOS output or an open drain output by setting
the corresponding bit in the GPIO Output Mode Register. Each GPIO pin configured as an output will reflect the value
held in the GPIO Data Register with a logic 0 causing the pin to be low and a logic 1 causing the pin to be high.
Reading from the GPIO Data Register will return the last value written to it.
When configured as an input, each GPIO can be configured as level or edge sensitive by setting the corresponding bit in
the GPIO Input Mode Select Register. When set to level sensitive, the corresponding bit in the GPIO Data Register will
follow the logic level of the GPIO pin. When set to edge sensitive the corresponding bit in the GPIO Data Register will
change from a logic 0 to a logic 1 when the input transitions from low to high (rising edge) or high to low (falling edge) as
determined by the setting in the GPIO Input Edge Select Register. The value in the GPIO Data Register will remain a
logic 1 until a logic 0 is written into the register throuigh host or I2C interface. In level sensitive mode, writing to the
GPIO Data Register through host or I2C will have no effect.
When configured as an input, a GPIO may also generate an interrupt. Interrupts are always edge sensitive. The GPIO
Input Edge Select Register is used to select which edge, rising or falling, is used to generate an interrupt. When as edge
is detected, the GPIO Interrupt Status Register will show a logic 1 in the corresponding bit and an interrupt will be
generated provided the appropriate bit has been enabled by writing a
logic 1 to the GPIO Interrupt Enable Register. The
GPIO Interrupt Status Register is cleared by writing a logic 1 to the appropriate bit. Writing a logic 0 will have no effect.
13.7 PCON REGISTERS
13.7.1
GPIO DIRECTION REGISTER
IC Address = Page-0: 32(0x20), C Address = 0xA020
IC Address = Page-0: 33(0x21), C Address = 0xA021
Bit
Bit Name
Def.
Set.
User
Type
Value
Description / Comments
0
RESERVED
0b
R/W
RESERVED
[10:1]
GPIO_DIR
0000000000b
R/W
0 = Input
1 = Output
Each bit sets the corresponding GPIO to either input or output
[15:11]
RESERVED
R/W
RESERVED
13.7.2
GPIO DATA REGISTER
IC Address = Page-0: 34(0x22), C Address = 0xA022
IC Address = Page-0: 35(0x23), C Address = 0xA023
相關PDF資料
PDF描述
PBL3717A STEPPER MOTOR CONTROLLER, 1.2 A, PDIP16
PC13892AJVL 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA186
PC13892BJVK 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA139
PC13892AJVK 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA139
PC13892BJVL 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA186
相關代理商/技術參數
參數描述
P95021NQG 功能描述:PMIC 解決方案 Integrates Audio, LED B/Light Pwr Mgt RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
P95021NQG8 制造商:Integrated Device Technology Inc 功能描述:POWER MANAGEMENT, AUDIO & CONT 制造商:Integrated Device Technology Inc 功能描述:132-VFQFPN - Tape and Reel 制造商:Integrated Device Technology Inc 功能描述:Integrates Audio, LED B/Light Pwr Mgt
P950-36I 制造商:Tripp Lite 功能描述:SERIAL ATA II SIGNAL CABLE, 2X7-PIN STRAIGHT CONNECTOR - 39" - Bulk
P9508- 制造商:ROEBUCK 功能描述:ROEBUCK DISH WASHING BRUSH
P9-511121 功能描述:按鈕開關 Flush Dome Solder 5A SPST-DB, SPDT-DB RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 安裝風格: 照明: 照明顏色: IP 等級: 端接類型: 觸點電鍍: 執行器: 蓋顏色: 封裝: 可燃性等級:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*