- 您現在的位置：買賣IC網 > PDF目錄363670 > NT7501H-BDT (Electronic Theatre Controls, Inc.) 33 X 100 RAM-Map LCD Controller/Driver PDF資料下載
參數資料
| 型號： | NT7501H-BDT |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 33 X 100 RAM-Map LCD Controller/Driver |
| 中文描述： | 33 × 100 RAM的地圖LCD控制器/驅動器 |
| 文件頁數： | 21/38頁 |
| 文件大?。?/td> | 319K |
| 代理商： | NT7501H-BDT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
NT7501
21
10. Entire Display ON
Forcibly turns the entire display on regardless of the contents of the display data RAM. At this time, the contents of the
display data RAM are held.
This command has priority over the Normal/Reverse Display command. When D is low, the normal display status is
provided.
A0
E
RD
W
R
WR
0
D7
D6
D5
D4
D3
D2
D1
D0
0
1
1
0
1
0
0
1
0
D
When D is high, the Entire display ON status is provided. If the Entire Display ON command is executed during the display
OFF status, the LCD panel enters Power Save mode. Refer to the Power Save section for details.
11. Set LCD Bias
Selects a bias ratio for the voltage required for driving the LCD. This command is enabled when the voltage follower in the
power supply circuit operates.
A0
E
RD
W
R
WR
0
D7
D6
D5
D4
D3
D2
D1
D0
0
1
1
0
1
0
0
0
1
D
The potential V0 is resistively divided inside the IC to produce potentials V1, V2, V3 and V4 which are necessary to drive
the LCD. The bias ratio can be selected using the LCD bias setting command.
Moreover, the potentials V1, V2, V3 and V4 are converted in the impedance and supplied to the LCD drive circuit.
Duty
Bias ratio of LCD power supply
1/33
1/5 bias or 1/6 bias
12. Read-Modify-Write
A pair of Read-Modify-Write and End commands must always be used. Once a Read-Modify-Write is issued, the column
address is not incremental by the Read Display Data command but incremented by the Write Display Data command only.
It continues until the End command is issued. When the End command is issued, the column address returns to the
address before the Read-Modify-Write was issued. This can reduce the microprocessor load when data of a specific
display area is repeatedly changed during cursor blinking or others.
A0
E
RD
W
R
WR
0
D7
D6
D5
D4
D3
D2
D1
D0
0
1
1
1
1
0
0
0
0
0
Note:
Any command except Read/Write Display Data and Set Column Address can be issued during Read-Modify-
Write mode.
相關PDF資料 |
PDF描述 |
|---|---|
| NT7502 | 65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-BDT | 65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-TABF1 | 65 X 132 RAM-Map LCD Controller / Driver |
| NT7603 | 2 x 110 W class-D power amplifer, SOT566-3 (HSOP24), Reel Pack, SMD, 13" |
| NT7603BDB-01 | Class D Audio Amplifier, SOT549-1 (HTSSOP32), Reel Dry Pack, SMD, 13" |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NT7502 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-BDT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-TABF1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:65 X 132 RAM-Map LCD Controller / Driver |
| NT75-1 | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Low coil consumption. / Switching capacity up to 16A. |
| NT751AS12DC110V | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Switching capacity up to 16A. |
發布緊急采購，3分鐘左右您將得到回復。