- 您現在的位置：買賣IC網 > PDF目錄363670 > NT7501H-BDT (Electronic Theatre Controls, Inc.) 33 X 100 RAM-Map LCD Controller/Driver PDF資料下載
參數資料
| 型號： | NT7501H-BDT |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 33 X 100 RAM-Map LCD Controller/Driver |
| 中文描述： | 33 × 100 RAM的地圖LCD控制器/驅動器 |
| 文件頁數： | 16/38頁 |
| 文件大?。?/td> | 319K |
| 代理商： | NT7501H-BDT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
NT7501
16
Command Sequence when Built-in Power Supply is Turned OFF
To turn off the built-in power supply, follow the command sequence as shown below after setting the system to standby mode.
Static Indicator ON
Display OFF
Entire Display ON
Command ADH
Command AEH
Command A5H
Built-in Power OFF
}
Power Save
Command
Reset Circuit
When the RES input goes low, this LSI is initialized.
Initialized status
1. Display OFF
2. Normal display
3. ADC select: Normal display (ADC command D0 = low)
4. Read modify write OFF
5. Power control register (D2, D1, D0) = (0, 0, 0,)
6. Register data clear in serial interface
7. LCD power supply bias ratio 1/6
8. Static indicator: OFF
9. Display start line register set at line 1
10. Column address counter set at address0
11. Page address register set at page 0
12. Output status register (D3) = (0)
13. Electronic control register set at 0
14. Test command OFF
As seen in Figure 8 Microprocessor Interface (Reference Example). Connect the RES pad to the reset pin of the
microprocessor and initialize the microprocessor at the same time.
In case the NT7501 does not use the internal LCD power supply circuit, the RES must be low when the external LCD power
supply is turned on.
When RES goes low, each register is cleared and set to the above initialized status. However, it has no effect on the oscillator
circuit and output pads (FR, CL, DYO, D0 to D7)
The initialization by RES pad signal is always required during power-on. If the control signal from the MPU is HZ, an
overcurrent may flow through the IC. A protection is required to prevent the HZ signal at the input pads during power-on.
Be sure to initialize it by RES pad when turning on the power supply. When the reset command is used, only parameters 8 to
14 in the above initialization are executed.
相關PDF資料 |
PDF描述 |
|---|---|
| NT7502 | 65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-BDT | 65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-TABF1 | 65 X 132 RAM-Map LCD Controller / Driver |
| NT7603 | 2 x 110 W class-D power amplifer, SOT566-3 (HSOP24), Reel Pack, SMD, 13" |
| NT7603BDB-01 | Class D Audio Amplifier, SOT549-1 (HTSSOP32), Reel Dry Pack, SMD, 13" |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NT7502 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-BDT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-TABF1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:65 X 132 RAM-Map LCD Controller / Driver |
| NT75-1 | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Low coil consumption. / Switching capacity up to 16A. |
| NT751AS12DC110V | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Switching capacity up to 16A. |
發布緊急采購，3分鐘左右您將得到回復。