- 您現在的位置：買賣IC網 > PDF目錄363670 > NT7501H-BDT (Electronic Theatre Controls, Inc.) 33 X 100 RAM-Map LCD Controller/Driver PDF資料下載
參數資料
| 型號： | NT7501H-BDT |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 33 X 100 RAM-Map LCD Controller/Driver |
| 中文描述： | 33 × 100 RAM的地圖LCD控制器/驅動器 |
| 文件頁數： | 12/38頁 |
| 文件大?。?/td> | 319K |
| 代理商： | NT7501H-BDT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
NT7501
12
Display Data Latch Circuit
This circuit temporarily stores (or latches) display data (during a single common signal period) when it is output from display
RAM to LCD panel driver circuit. This latch is controlled by Display in normal/reverse Display ON/OFF and Entire display on
commands. These commands do not alter the data.
LCD Driver
This is a multiplexer circuit consisting of 100 segment outputs to generate four-level LCD panel drive signals. The LCD panel
drive voltage is generated by a specific combination of display data, a COM scan signal, and a FR signal. Figure 5 gives an
example of SEG and COM output waveform.
Oscillator Circuit
This is an oscillator having a complete built-in type CR, and its output is used as the display timing signal source or as the clock
for the voltage booster circuit of the LCD power supply.
The oscillator circuit is available in master mode only.
The oscillator signal is divided and output as a display clock at the CL pad.
Power Supply Circuit
The power supply circuit generates voltage to drive the LCD panel at low power consumption, and is available in NT7501
master mode only. The power supply circuit consists of a voltage booster, a voltage regulator and a LCD drive voltage follower.
The power supply circuit built into the NT7501 is set for a small-scale LCD panel and is inappropriate for a large-pixel panel and
a large-display-capacity LCD panel using multiple chips. As the large LCD panel has the dropped display quality due to a large
load capacity, it must use an external power source.
The power circuit is controlled by the Set Power Control command. This command sets a three-bit data in the Power Control
register to select one of eight power circuit functions. The external power supply and part of the internal power circuit functions
can be used simultaneously. The following explains how the Set Power Control command works.
[Control by Set Power Control command]
D2 turns on when the voltage booster control bit goes high, and D2 turns off when this bit goes low.
D1 turns on when the voltage regulator control bit goes high, and D1 turns off when this bit goes low.
D0 turns on when the voltage follower control bit goes high, and D0 turns off when this bit goes low.
[Practical combination examples]
Status 1: To use only the internal power supply
Status 2: To use only the voltage regulator and voltage follower
Status 3: To use only the voltage follower, input the external voltage V
0
Status 4: To use only an external power supply because the internal power supply does not operate
D2
D1
D0
Voltage
booster
Voltage
regulator
Voltage
follower
External
voltage
input
Voltage
booster
terminal
Voltage
regulator
terminal
1
1
1
1
ON
ON
ON
-
Used
Used
2
0
1
1
OFF
ON
ON
VOUT
OPEN
Used
3
0
0
1
OFF
OFF
ON
V0
OPEN
OPEN
4
0
0
0
OFF
OFF
OFF
V0 to V4
OPEN
OPEN
* The voltage booster terminals are CAP1+, CAP1-, CAP2+, CAP2- and CAP3+
* Combinations other than those shown in the above table are possible but impractical.
相關PDF資料 |
PDF描述 |
|---|---|
| NT7502 | 65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-BDT | 65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-TABF1 | 65 X 132 RAM-Map LCD Controller / Driver |
| NT7603 | 2 x 110 W class-D power amplifer, SOT566-3 (HSOP24), Reel Pack, SMD, 13" |
| NT7603BDB-01 | Class D Audio Amplifier, SOT549-1 (HTSSOP32), Reel Dry Pack, SMD, 13" |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NT7502 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-BDT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-TABF1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:65 X 132 RAM-Map LCD Controller / Driver |
| NT75-1 | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Low coil consumption. / Switching capacity up to 16A. |
| NT751AS12DC110V | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Switching capacity up to 16A. |
發布緊急采購，3分鐘左右您將得到回復。