- 您現在的位置：買賣IC網 > PDF目錄363665 > NSAM266SA (NATIONAL SEMICONDUCTOR CORP) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | NSAM266SA |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 數字信號處理 |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 8-BIT, MIXED DSP |
| 文件頁數： | 25/52頁 |
| 文件大?。?/td> | 571K |
| 代理商： | NSAM266SA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
2.0 Software
(Continued)
A message is the basic unit on which most of the Compact-
SPEECH commands operate. A CompactSPEECH mes-
sage, stored on a flash device, can be regarded as a com-
puter file stored on a mass-storage device.
A message is created with either the R or the WRAM (Write
Memory) command.
When a message is created, it is assigned a time-and-day
stamp and a message tag which can be read by the micro-
controller.
The R command takes voice samples from the codec, com-
presses them, and stores them in the message memory.
When a message is created with the WRAM command the
data to be recorded is provided by the microcontroller and
not via the codec. The data is transferred directly to the
message memory. It is not compressed by the Compact-
SPEECH voice compression algorithm.
The WRAM command, together with the RRAM (Read
Memory) command which enables the microcontroller to
read data from the CompactSPEECH, can be used to store
data other than compressed voice in the message memory
e.g., a telephone directory.
A message can be played back (P command) and deleted
(DM command). Redundant data (e.g., trailing tones or si-
lence) can be removed from the message tail with the CMT
(Cut Message Tail) command.
The PA (Pause) and RES (Resume) commands, respective-
ly, temporarily suspend the P and R commands, and then
allow them to resume execution from where they were sus-
pended.
CURRENT MESSAGE
Most message handling commands, e.g., P, DM, RRAM, op-
erate on the current message. The GTM (Get Tagged Mes-
sage) command selects the current message.
Deleting the current message does not cause a different
message to become current. The current message is unde-
fined. If, however, you issue the GTM command to skip to
the next message, the first message that is newer than the
just deleted message is selected as the current message.
2.6.1 Message Tag
Each message has a 2-byte message tag which you can
use to categorize messages, and implement such features
as OutGoing Messages, mailboxes, and different handling
of old and new messages.
The most significant bit (bit 15) of the message tag is used
to indicate the speech compression rate. The microcontrol-
ler should program it before recording (‘‘1’’ for 4.8 kbit/s,
‘‘0’’ for 6.6 kbit/s). The CompactSPEECH reads the bit be-
fore message playback to select the appropriate decom-
pression algorithm.
The GMT (Get Message Tag) and SMT commands may be
used to handle message tags.
Note:
Message tag bits can only be cleared. Message tag bits are set only
when a message is first created.
This limitation is inherent in flash memories, which only allow bits to
be changed from 1 to 0 (changing bits from 0 to 1 requires a special
erasure procedure, see Section 1.3.5). However, the main reason for
updating an existing tag is to mark a message as old, and this can be
done by using one of the bits as a new/old indicator, setting it to 1
when a message is first created, and clearing it when necessary.
2.7 SPEECH COMPRESSION
The CompactSPEECH implements two speech compres-
sion algorithms. One algorithm, with 5.2 kbit/s compression
rate, enables up to 14–16 minutes of recording on a 4-Mbit
device, while the other uses a 7.3 kbit/s compression rate
to support 10–12 minutes of recording. Both compression
rates assume 10% silence.
Before recording each message, the microcontroller can se-
lect one of the two algorithms by programming bit 15 of the
message tag. During message playback the Compact-
SPEECH reads this bit and selects the appropriate speech
decompression algorithm.
IVS vocabularies can be prepared in either of the two com-
pression formats using the IVS tool. All the messages in a
single vocabulary must be recorded using the same algo-
rithm. (See theIVS User’s Manual for further details). During
speech synthesis, the CompactSPEECH automatically se-
lects the appropriate speech decompression algorithm.
2.8 TONE AND NO-ENERGY DETECTION
The CompactSPEECH detects DTMF, busy, and dial tones,
and no-energy (VOX). This enables remote control opera-
tions and call progress. Detection is active throughout the
operation of the CompactSPEECH. Detection can be con-
figured using the SDET (Set Detectors Mask) command,
which controls the reporting of the occurrence of tones, and
the RDET (Reset Detectors) command which resets the de-
tectors.
DTMF
DTMF detection may be reported at the starting point, end-
ing point, or both. The report is made through the status
word (for further details, see GSW command in Section
2.14).
The DTMF detector performance, as measured on the line
input using an NSV-AM265-DAA board, is summarized be-
low (see Table 2-1).
ECHO CANCELLATION
Echo cancellation is a technique used to improve the per-
formance of DTMF tone detection during speech synthesis,
tone generation, and OGM playback. For echo cancellation
to work properly, AGC must not be active in parallel. Thus,
to take advantage of echo cancellation, the microcontroller
must control the AGC, i.e., disable the AGC during
PLAY,
SYNTHESIS
and
TONEDGENERATE
states and enable it
again afterwards. If AGC cannot be disabled, do not use
echo cancellation. The microcontroller should use the CFG
command to activate/deactivate echo cancellation. (For fur-
ther details, see Section 2.14.)
Echo cancellation applies only to DTMF tones. Busy and
dial-tone detection is not affected by this technique. This
implies that the performance of the busy and dial-tone de-
tector during message playback depends on the message
being played.
http://www.national.com
25
相關PDF資料 |
PDF描述 |
|---|---|
| NSAM266SAA | 4 Mbit Uniform Sector, Serial Flash Memory |
| NSB8 | BASIC interpreter for Z80 family |
| NSB9435T1 | High Current Bias Resistor Transistors(高強度電流偏置電阻晶體管) |
| NSBA114EDXV6T1 | Dual Bias Resistor Transistors(雙偏置電阻晶體管) |
| NSBA114YDXV6T1 | Dual Bias Resistor Transistors(雙偏置電阻晶體管) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NSAM266SAA | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:NSAM266SA CompactSPEECHTM Digital Speech Processor with Serial Flash Interface |
| NSAM266SAA/V | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:NSAM266SA CompactSPEECHTM Digital Speech Processor with Serial Flash Interface |
| NSAM266SAA/VLJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Solid-State Recorder |
| NSAM266SC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| NSAM266SCA/V | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Solid-State Recorder |
發布緊急采購，3分鐘左右您將得到回復。