參數資料
型號： NS16C2752
廠商： National Semiconductor Corporation
英文描述： Dual UART with 16-byte/64-byte FIFOs and up to 5 Mbit/s Data Rate
中文描述： 雙UART與16-byte/64-byte FIFO和高達5 Mbit / s的數據速率
文件頁數： 29/43頁
文件大?。?/td> 881K
代理商： NS16C2752
7.0 Operation and Configuration
(Continued)
DMA Mode
In the non-FIFO mode, the presence of a received character
in RBR causes the assertion of RXRDY at which point DMA
transfer can be initiated. Upon transfer completion RXRDY is
deasserted. DMA transfer stops and awaits for the next
character. (
Figure 7
.)
7.3.3 Receive Hardware Flow Control
On the line side, RTS signal provides automatic flow control
to prevent data overflow in the Receive FIFO. The RTS is
used to request remote unit to suspend or resume data
transmission. This feature is enabled to suit specific applica-
tion. The RTS flow control can be enabled by the following
steps:
Enable auto-RTS flow control EFR[6]=1.
The auto-RTS function is initiated by asserting RTS out-
put pin, MCR[1]=1.
The auto-RTS assertion and deassertion timing is based
upon the Rx FIFO trigger level (
Table 27
and
Table 28
).
7.3.4 Receive Flow Control Interrupt
To enable auto RTS interrupt:
Enable auto RTS flow control EFR[6]=1.
Enable RTS interrupt IER[6]=1.
An interrupt is generated when RTS pin makes a transition
from logic 0 to 1; IIR[5] is set to logic 1.
The receive data ready interrupt (IIR[2]) generation timing is
based upon the Rx FIFO trigger level (Table 27 and Table
28).
TABLE 27. Auto-RTS HW Flow Control on NS16C2552
Rx Trigger
Level
1
4
8
14
INTR Pin
Activation
1
4
8
14
RTS
Desertion
2
8
14
14
RTS
Assertion
0
1
4
8
TABLE 28. Auto-RTS HW flow Control on NS16C2752
Rx Trigger
Level
8
16
56
60
INTR Pin
Activation
8
16
56
60
RTS
Desertion
16
56
60
60
RTS
Assertion
0
8
16
56
7.4 TRANSMIT OPERATION
Each serial channel consists of an 8-bit Transmit Shift Reg-
ister (TSR) and a 16-byte (or 64-byte) Transmit FIFO. The
Transmit FIFO includes a 8-bit Transmit Holding Register
(THR). The TSR shifts data out at the 16X internal clock. A
bit time is 16 clock periods. The transmitter begins with a
start-bit followed by data bits, asserts parity-bit if enabled,
and adds the stop-bit(s). The FIFO and TSR status is re-
ported in the LSR[6:5].
The THR is an 8-bit register providing a data interface to the
host processor. The host writes transmit data to the THR.
The THR is the Transmit FIFO input register in FIFO opera-
tion. The FIFO operation can be enabled by FCR[0]=1.
During the FIFO operation, the FIFO pointer is incremented
pointing to the next FIFO location when a data word is
written into the THR.
7.4.1 Transmit in FIFO Mode
Interrupt mode
In the NS16C2752 FIFO mode (FCR[0]=1), when the Tx
FIFO empty spaces exceed the threshold level the THR
empty flag is set (LSR[5]=1). The THR empty flag generates
20204808
FIGURE 6. Rx Non-FIFO Mode
20204809
FIGURE 7. RXRDY in DMA Mode 0
N
www.national.com
29
相關PDF資料
PDF描述
NS16C2752TVA Dual UART with 16-byte/64-byte FIFOs and up to 5 Mbit/s Data Rate
NS32203D DIRECT MEMORY ACCESS CONTROLLER
NS32203N DIRECT MEMORY ACCESS CONTROLLER
NS32382-10 MEMORY MANAGEMENT UNITS
NS32382-15 MEMORY MANAGEMENT UNITS
相關代理商/技術參數
參數描述
NS16C2752TVA 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Dual UART with 16-byte/64-byte FIFOs and up to 5 Mbit/s Data Rate
NS16C2752TVA/NOPB 功能描述:UART 接口集成電路 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
NS16C2752TVAX/NOPB 功能描述:UART 接口集成電路 Dual UART w/ 64-byte FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
NS16C2752TVS 制造商:Texas Instruments 功能描述:UART 2-CH 64Byte FIFO 3.3V/5V 48-Pin TQFP
NS16C2752TVS/NOPB 功能描述:UART 接口集成電路 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*