- 您現在的位置：買賣IC網 > PDF目錄363250 > NE962R575 (NEC Corp.) 0.5 W X, Ku-BAND POWER GaAs MES FET PDF資料下載
參數資料
| 型號： | NE962R575 |
| 廠商： | NEC Corp. |
| 英文描述： | 0.5 W X, Ku-BAND POWER GaAs MES FET |
| 中文描述： | 0.5蠟質，Ku波段功率GaAs場效應晶體管 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 62K |
| 代理商： | NE962R575 |
Preliminary Data Sheet P14387EJ1V0DS00
8
NE960R5 SERIES
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered under the following recommended conditions. For soldering methods and
conditions other than those recommended below, contact your NEC sales representative.
Soldering Method
Soldering Conditions
Recommended Condition Symbol
Partial Heating
Pin temperature: 260
°
C
Time: 5 seconds or less (per pin row)
Exposure limit: None
Note
–
Note
After opening the dry pack, keep it in a place below 25
°
C and 65 % RH for the allowable storage period.
Caution Do not use different soldering methods together (except for partial heating).
CHIP HANDLING
DIE ATTACHMENT
Die attach can be accomplished with a Au-Sn (300
±
10
°
C) performs in a forming gas environment. Epoxy die
attach is not recommended.
BONDING
Gate and drain bonding wires should be minimum length, semi-hard gold wire (3 to 8 % elongation) 30 microns or
less in diameter.
Bonding should be performed with a wedge tip that has a taper of approximately 15 %.
Die attach and bonding time should be kept to a minimum. As a general rule, the bonding operation should be
kept within a 280
°
C_5 minute curve. If longer periods are required, the temperature should be lowered.
PRECAUTIONS
The user must operate in a clean, dry environment.
The chip channel is glassivated for mechanical protection only and does not preclude the necessity of a clean
environment.
The bonding equipment should be periodically checked for sources of surge voltage and should be properly
grounded at all times. In fact, all test and handling equipment should be grounded to minimize the possibilities of
static discharge.
相關PDF資料 |
PDF描述 |
|---|---|
| NE97733 | PNP SILICON HIGH FREQUENCY TRANSISTOR |
| NE97733-T1 | PNP SILICON HIGH FREQUENCY TRANSISTOR |
| NE97833 | PNP SILICON HIGH FREQUENCY TRANSISTOR |
| NE97833-T1 | PNP SILICON HIGH FREQUENCY TRANSISTOR |
| NECW008AT | NICHIA CHIP TYPE WHITE LED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NE97733 | 功能描述:射頻雙極小信號晶體管 PNP High Frequency RoHS:否 制造商:NXP Semiconductors 配置:Single 晶體管極性:NPN 最大工作頻率:7000 MHz 集電極—發射極最大電壓 VCEO:15 V 發射極 - 基極電壓 VEBO:2 V 集電極連續電流:0.15 A 功率耗散:1000 mW 直流集電極/Base Gain hfe Min: 最大工作溫度:+ 150 C 封裝 / 箱體:SOT-223 封裝:Reel |
| NE97733-A | 功能描述:射頻雙極小信號晶體管 PNP High Frequency RoHS:否 制造商:NXP Semiconductors 配置:Single 晶體管極性:NPN 最大工作頻率:7000 MHz 集電極—發射極最大電壓 VCEO:15 V 發射極 - 基極電壓 VEBO:2 V 集電極連續電流:0.15 A 功率耗散:1000 mW 直流集電極/Base Gain hfe Min: 最大工作溫度:+ 150 C 封裝 / 箱體:SOT-223 封裝:Reel |
| NE97733-T1 | 制造商:California Eastern Laboratories (CEL) 功能描述:Trans GP BJT PNP 12V 0.05A 3-Pin SOT-23 T/R |
| NE97733-T1-A | 功能描述:射頻雙極小信號晶體管 PNP High Frequency RoHS:否 制造商:NXP Semiconductors 配置:Single 晶體管極性:NPN 最大工作頻率:7000 MHz 集電極—發射極最大電壓 VCEO:15 V 發射極 - 基極電壓 VEBO:2 V 集電極連續電流:0.15 A 功率耗散:1000 mW 直流集電極/Base Gain hfe Min: 最大工作溫度:+ 150 C 封裝 / 箱體:SOT-223 封裝:Reel |
| NE97733-T1B-A | 功能描述:射頻雙極小信號晶體管 PNP Silicon HI Freq Transist 8.5GHzfT RoHS:否 制造商:NXP Semiconductors 配置:Single 晶體管極性:NPN 最大工作頻率:7000 MHz 集電極—發射極最大電壓 VCEO:15 V 發射極 - 基極電壓 VEBO:2 V 集電極連續電流:0.15 A 功率耗散:1000 mW 直流集電極/Base Gain hfe Min: 最大工作溫度:+ 150 C 封裝 / 箱體:SOT-223 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。