參數資料
型號： NCN6001DTBEVB
廠商： ON Semiconductor
文件頁數： 33/36頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR NCN6001DTB
設計資源： NCN6001DTBEVB Gerber Files
NCN6001 Demo Brd Schematic
NCN6001DBEVB BOM
標準包裝： 1
主要目的： 接口，智能卡
嵌入式： 是，MCU，8 位
已用 IC / 零件： NCN6001
主要屬性： 與 ISO 7816-3，EMV，GIE-CB 兼容
次要屬性： 符合 GSM 規定
已供物品： 板
其它名稱： NCN6001DTBEVBOS
NCN6001
http://onsemi.com
6
PIN FUNCTIONS AND DESCRIPTION
TSSOP
Description
Type
Name
LLGA
18
15
CRD_DET
INPUT
The signal coming from the external card connector is used to detect the presence of
the card. A builtin pullup low current source biases this pin High, making it active
LOW, assuming one side of the external switch is connected to ground. A builtin
digital filter protect the system against voltage spikes present on this pin.
The polarity of the signal is programmable by the MOSI message, according to the
logic state depicted Table 2. On the other hand, the meaning of the feedback
message contained in the MISO register bit b4, depends upon the SPI mode of
operation as defined here below:
SPI Normal Mode: The MISO bit b4 is High when a card is inserted, whatever be the
polarity of the card detect switch.
SPI Special Mode: The MISO bit b4 copies the logic state of the Card detect switch as
depicted here below, whatever be the polarity of the switch used to handle the
detection:
CRD_DET = Low MISO/b4 = Low
CRD_DET = High MISO/b4 = High
In both cases, the chip must be programmed to control the right logic state (Table 2).
Since the bias current supplied by the chip is very low, typically 5.0 mA, care must be
observed to avoid low impedance or cross coupling when this pin is in the Open state.
19
16
CRD_RST
OUTPUT
This pin is connected to the RESET pin of the card connector. A level translator
adapts the RESET signal from the microcontroller to the external card. The output
current is internally limited to 15 mA.
The CRD_RST is validated when CS = Low and hard wired to Ground when the card
is deactivated, by and internal active pull down circuit.
Care must be observed, at PCB design level, to avoid cross coupling between this
signal and the CRD_CLK clock.
20
17
CRD_IO
I/O
Pullup
This pin handles the connection to the serial I/O pin of the card connector. A
bidirectional level translator adapts the serial I/O signal between the card and the
microcontroller. An internal active pull down MOS device forces this pin to Ground
during either the CRD_VCC startup sequence, or when CRD_VCC = 0 V. The
CRD_IO pin current is internally limited to 15 mA.
Care must be observed, at PCB design level, to avoid cross coupling between this
signal and the CRD_CLK clock.
相關PDF資料
PDF描述
2474-12L INDUCTOR 8.2UH POWER AXIAL
0982661043 CBL 33POS 0.5MM JMPR TYPE A 7"
UWT0G470MCL1GB CAP ALUM 47UF 4V 20% SMD
V48C5C100B CONVERTER MOD DC/DC 5V 100W
H3AAH-2406M IDC CABLE - HSC24H/AE24M/HSC24H
相關代理商/技術參數
參數描述
NCN6001DTBR2 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
NCN6001DTBR2G 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
NCN6001MUTWG 制造商:ON Semiconductor 功能描述:ANA COMPACT SMARTCARD IC - Tape and Reel 制造商:ON Semiconductor 功能描述:IC INTERFACE SMART CARD 制造商:ON Semiconductor 功能描述:REEL - ANA COMPACT SMARTCARD IC
NCN6004A 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Dual SAM/SIM Interface Integrated Circuit
NCN6004A/D 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Dual SAM/SIM Interface Integrated Circuit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*