- 您現在的位置：買賣IC網 > PDF目錄359235 > MT9160AN1 (Zarlink Semiconductor Inc.) 3 Volt Multi-Featured Codec (MFC) PDF資料下載
參數資料
| 型號： | MT9160AN1 |
| 廠商： | Zarlink Semiconductor Inc. |
| 元件分類： | Codec |
| 英文描述： | 3 Volt Multi-Featured Codec (MFC) |
| 中文描述： | 3伏多精選編解碼器（MFC）中 |
| 文件頁數： | 17/33頁 |
| 文件大?。?/td> | 527K |
| 代理商： | MT9160AN1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
MT91L60/61
Data Sheet
17
Zarlink Semiconductor Inc.
Note: Bits marked "-" are reserved bits and should be written with logic "0"
DrGain
When high, the receive path is summed with the side tone path and is attenuated by 6dB.
When low, the receive path contains no side tone (default).
Path Control
ADDRESS = 02h WRITE/READ VERIFY
Power Reset Value
XX00 0000
7
6
5
4
3
2
1
0
-
-
-
-
-
-
DrGain
-
PDFDI
PDDR
When high, the FDI PLA and the Filter/Codec are powered down (default). When low, the FDI is active.
When high, the ear driver and Filter/Codec are powered down (default). In addition, in ST-BUS mode, the selected output channel
is tri-stated. In SSI mode the PCM output code will be -zero code during the valid strobe period. The output will be tri-stated
outside of the valid strobe and for the whole frame if no strobe is supplied. When low, the driver and Filter/Codec are active if
PDFDI is low.
When high, a software reset occurs performing the same function as the hardware reset (PWRST) except that the Rst bit remains
high and device remains powered up. A software reset can be removed only by writing this bit low or by means of a hardware reset
(PWRST). This bit is useful for quickly programming the Registers to the default Power Reset Values. When this bit is low, the
reset condition is removed allowing the registers to be modified
When high the transmit PCM stream is interrupted and replaced with quiet code; thus forcing the output code into a mute state
(only the output code is muted, the transmit microphone and transmit Filter/Codec are still functional). When low the full transmit
path functions normally (default).
When high the received PCM stream is interrupted and replaced with quiet code; thus forcing the receive path into a mute state.
When low the full receive path functions normally (default).
When high, the transmit B2 channel is functional in ST-BUS mode. When low, the transmit B1 channel is functional in ST-BUS
mode. Not used in SSI mode.
When high, the receive B2 channel is functional in ST-BUS mode. When low, the receive B1 channel is functional in ST-BUS
Rst
TxMute
RxMute
TxBsel
RxBsel
Control Register 1
ADDRESS = 03h WRITE/READ VERIFY
Power Reset Value
0000 0000
7
6
5
4
3
2
1
0
PDFDI
PDDR
TxBsel RxBsel
Rst
_
TxMute RxMute
相關PDF資料 |
PDF描述 |
|---|---|
| MT91610 | Programmable Ringing SLIC |
| MT91610AQ | Programmable Ringing SLIC |
| MT91610 | Analog Ringing SLIC |
| MT91610AQ | Analog Ringing SLIC |
| MT9162AN1 | 5 Volt Single Rail Codec |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9160AS | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MT9160B | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO2-CMOS 5 Volt Multi-Featured Codec (MFC) |
| MT9160BE | 制造商:Microsemi Corporation 功能描述:MULTI-FEATURED CODEC 24PDIP - Rail/Tube |
| MT9160BN | 制造商:Microsemi Corporation 功能描述: |
| MT9160BS | 制造商:Microsemi Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。