參數資料
型號： MC68HC05C9ECP
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP40
封裝： PLASTIC, DIP-40
文件頁數： 70/106頁
文件大?。?/td> 659K
代理商： MC68HC05C9ECP
Serial Peripheral Interface (SPI)
MC68HC05C9E Advance Information Data Sheet, Rev. 0.1
66
Freescale Semiconductor
10.5.2 Serial Peripheral Status Register
The SPI status register (SPSR), shown in Figure 10-5, contains flags to signal these conditions:
SPI transmission complete
Write collision
Mode fault
SPIF — SPI Transfer Complete Flag
The serial peripheral data transfer flag bit is set upon completion of data transfer between the
processor and external device. If SPIF goes high, and if SPIE is set, a serial peripheral interrupt is
generated. Clearing the SPIF bit is accomplished by reading the SPSR (with SPIF set) followed by an
access of the SPDR. Following the initial transfer, unless SPSR is read (with SPIF set) first, attempts
to write to SPDR are inhibited.
WCOL — Write Collision Bit
The write collision bit is set when an attempt is made to write to the serial peripheral data register while
data transfer is taking place. If CPHA is 0, a transfer is said to begin when SS goes low and the transfer
ends when SS goes high after eight clock cycles on SCK. When CPHA is 1, a transfer is said to begin
the first time SCK becomes active while SS is low and the transfer ends when the SPIF flag gets set.
Clearing the WCOL bit is accomplished by reading the SPSR (with WCOL set) followed by an access
to SPDR.
MODF — Mode Fault Flag
The mode fault flag indicates that there may have been a multi-master conflict for system control and
allows a proper exit from system operation to a reset or default system state. The MODF bit is normally
clear, and is set only when the master device has its SS pin pulled low. Setting the MODF bit affects
the internal serial peripheral interface system in these ways:
1.
An SPI interrupt is generated if SPIE = 1.
2.
The SPE bit is cleared. This disables the SPI.
3.
The MSTR bit is cleared, thus forcing the device into the slave mode.
Clearing the MODF bit is accomplished by reading the SPSR (with MODF set), followed by a write to
the SPCR. Control bits SPE and MSTR may be restored by user software to their original state during
this clearing sequence or after the MODF bit has been cleared. It is also necessary to restore DDRD
after a mode fault.
Bits 5 and 3–0 — Not Implemented
These bits always read 0.
Address:
$000B
Bit 7
654321
Bit 0
Read:
SPIF
WCOL
0
MODF
0000
Write:
Reset:
00000000
= Unimplemented
Figure 10-5. SPI Status Register
相關PDF資料
PDF描述
MC68HC05CC2B 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDIP42
MC68HC05CJ4FB 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44
MC68HC705CJ4FB 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQFP44
MC68HC05E0FN 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQCC68
MC68HC05E5P 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP28
相關代理商/技術參數
參數描述
MC68HC05CT4FB 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification
MC68HC05CT4FN 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification
MC68HC05D9 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-bit microcomputer with PWM outputs and LED drive
MC68HC05E0 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:High-density complementary metal oxide semiconductor (HCMOS) microcontroller unit
MC68HC05E0FN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*