參數資料
型號： MC145202-1
廠商： Motorola, Inc.
英文描述： PLL Frequency Synthesizer(2.0GHz PLL頻率合成器)
中文描述： 鎖相環頻率合成器（2.0GHz的鎖相環頻率合成器）
文件頁數： 13/23頁
文件大?。?/td> 270K
代理商： MC145202-1
MC145202–1
13
MOTOROLA WIRELESS SEMICONDUCTOR
SOLUTIONS – RF AND IF DEVICE DATA
ENB
CLK
Din
MSB
LSB
C7
C6
C5
C4
C3
C2
C1
C0
1
2
3
4
5
6
7
8
NOTE
NOTE:
At this point, the new byte is transferred to the C register and stored. No other
registers are affected.
Figure 14. C Register Access and Format
(8 Clock Cycles are Used)
C7 – POL:
Selects the output polarity of the phase/frequency detectors. When set high, this bit inverts PDout
and interchanges the
φ
R function with
φ
V as depicted in Figure 17. Also see the phase detector output
pin descriptions for more information. This bit is cleared low at power up.
C6 – PDA/B:
Selects which phase/frequency detector is to be used. When set high, enables the output of
phase/frequency detector A (PDout) and disables phase/frequency detector B by forcing
φ
R and
φ
V
to the static high state. When cleared low, phase/frequency detector B is enabled (
φ
R and
φ
V) and
phase/frequency detector A is disabled with PDout forced to the high–impedance state. This bit is
cleared low at power up.
C5 – LDE:
Enables the lock detector output when set high. When the bit is cleared low, the LD output is forced
to a static low level. This bit is cleared low at power up.
C4 – STBY:
When set, places the CMOS section of device, which is powered by the VDD and VPD pins, in the
standby mode for reduced power consumption: PDout is forced to the high–impedance state,
φ
R and
φ
V are forced high, the A, N, and R counters are inhibited from counting, and the Rx current is shut
off. In standby, the state of LD is determined by bit C5. C5 low forces LD low (no change). C5 high
forces LD static high. During standby, data is retained in the A, R, and C registers. The condition
of REF/OSC circuitry is determined by the control bits in the R register: R13, R14, and R15. However,
if REFout = static low is selected, the internal feedback resistor is disconnected and the input is inhibited
when in standby; in addition, the REFin input only presents a capacitive load. NOTE: Standby does
not affect the other modes of the REF/OSC circuitry.
When C4 is reset low, the part is taken out of standby in two steps. First, the REFin (only in one
mode) resistor is reconnected, all counters are enabled, and the Rx current is enabled. Any fR and
fV signals are inhibited from toggling the phase/frequency detectors and lock detector. Second, when
the first fV pulse occurs, the R counter is jam loaded, and the phase/frequency and lock detectors
are initialized. Immediately after the jam load, the A, N, and R counters begin counting down together.
At this point, the fR and fV pulses are enabled to the phase and lock detectors. (Patented feature.)
C3, C2 – I2, I1:
Controls the PDout source/sink current per Tables 5 and 6. With both bits high, the maximum current
is available. Also, see C1 bit description.
C1 – Port:
When the Output A pin is selected as “Port” via bits A22 and A23, C1 determines the state of Output
A. When C1 is set high, Output A is forced high; C1 low forces Output A low. When Output A is
not
selected as “Port,” C1 controls whether the PDout step size is 10% or 25%. (See Tables 5 and
6.) When low, steps are 10%. When high, steps are 25%. Default is 10% steps when Output A is
selected as “Port.” The Port bit is not affected by the standby mode.
C0 – Out B:
Determines the state of Output B. When C0 is set high, Output B is high–impedance; C0 low forces
Output B low. The Out B bit is not affected by the standby mode. This bit is cleared low at power
up.
相關PDF資料
PDF描述
MC145225 Dual PLL Frequency Synthesizers With DACs and Voltage Multipliers(帶DACs和電壓乘法器的雙PLL頻率合成器)
MC145230 Dual PLL Frequency Synthesizers With DACs and Voltage Multipliers(帶DACs和電壓乘法器的雙PLL頻率合成器)
MC14528BCL Dual Monostable Multivibrator
MC14528 DEFLECTION PROCESSOR FOR MULTISYNC MONITORS
MC14528 Dual Monostable Multivibrator
相關代理商/技術參數
參數描述
MC14520B 制造商:Motorola Inc 功能描述: 制造商:ON Semiconductor 功能描述:
MC14520BAL 制造商:Motorola Inc 功能描述:Counter, Up, 4 Bit Binary, 16 Pin, Ceramic, DIP
MC14520BCP 功能描述:計數器移位寄存器 3-18V Dual BCD Up RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel
MC14520BCPG 功能描述:計數器移位寄存器 3-18V Dual BCD Up RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel
MC14520BDW 功能描述:計數器移位寄存器 3-18V Dual BCD Up RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*