參數資料
型號： MB86960APF-G
廠商： Fujitsu Limited
英文描述： NETWORK INTERFACE CONTROLLER with ENCODER/DECODER (NICE)
中文描述： 網絡接口控制器的編碼/解碼器（尼斯）
文件頁數： 28/65頁
文件大?。?/td> 488K
代理商： MB86960APF-G
MB86960
Two of the control bits allow reception of packets with
certain types of errors. The ACPT BAD PKTS bit, when
set, causes the receiver to retain and store in the buffer
packets with CRC, alignment and/or short length errors
provided there was no indication of collision during
reception. Likewise, the ACPT SHORT PKTS bit, when
set, allows the retention of short packets down to and
including only six bytes in length, excluding preamble
and CRC, provided there was no indication of collision
during reception and no alignment or CRC error. Under
normal operation, packets with less than 60 bytes, the
IEEE 802.3 lower limit, would be discarded. These
functions are provided for diagnostic purposes. Packets
are accepted only if both the address filter and the error
filter are passed. Packets with no content errors, i.e., short,
alignment or CRC, are accepted without regard to
collision indicators.
Table 11. DLCR5 — Receive Mode Register
BIT
SYMBOL
TYPE
DESCRIPTION
7
0
N
0
RESERVED:
Write 0.
6
RX BUF
EMTY
R
1
RECEIVE BUFFER EMPTY:
Status bit which indicates that the receive buffer does not have
any complete packets to read. (Read only).
5
ACPT
BAD
PKTS
R
W
0
ACCEPT PACKETS WITH ERRORS:
When set high, allows packets with CRC, alignment
and/or short length errors to be saved into the receive buffer for analysis, provided there was
no indication of collision during reception. Otherwise such packets would be discarded
automatically by the receiver and removed from the buffer. See also Table 8.
4
40 BIT
ADDR
R
W
0
40 BIT ADDRESS:
When set high, instead of the customary 48-bit NODE ID address filter,
only the first 40 bits of the NODE ID are compared (NODE ID 0–4).
3
ACPT
SHORT
PKTS
R
W
0
ACCEPT SHORT PACKETS:
When set high, allows short packets (packets with less than
60 bytes, excluding Preamble and CRC, i.e. below IEEE minimum length) down to 6 bytes,
excluding preamble and CRC, to be saved nto the receive buffer, provided there was no CRC
or alignment error and no indication of collision during reception. Otherwise such packets
would be discarded automatically by the receiver and removed from the buffer. See also Table
8.
2
1
N
0
RESERVED:
Write 1.
1
AF1
R
W
0
ADDRESS FILTER MODE:
AF1 and AF0, DLCR5<1:0>, control the address filtering on
incoming packets. See table below under AF0.
0
AF0
R
W
1
ADDRESS FILTER MODE:
AF1 and AF0, DLCR5<1:0>, control the address filtering on
incoming packets:
AF1
AF0
Description of Address Accepted
0
1
NODE ID, Broadcast, Multicast & 2nd-24th bits of NODE ID
1
0
NODE ID, Broadcast, Multicast & Hash Table
0
0
Reject all packets
1
1
Accept all packet
Note: Self reception of broadcast and multicast packets prohibited except in “Accept all
packets” mode. When LBC is low (loopback mode) broadcast packets can be
self-received, except in “Reject all packets” mode.
相關PDF資料
PDF描述
MB86961A UNIVERSAL INTERFACE FOR 10BASET
MB86961APD-G UNIVERSAL INTERFACE FOR 10BASET
MB86961APF-G UNIVERSAL INTERFACE FOR 10BASET
MB86965 EtherCoupler ETHERNET CONTROLLER WITH 10BASE?T TRANSCEIVER
MB86965B EtherCoupler ETHERNET CONTROLLER WITH 10BASE?T TRANSCEIVER
相關代理商/技術參數
參數描述
MB86961A 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:UNIVERSAL INTERFACE FOR 10BASET
MB86961APD-G 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:UNIVERSAL INTERFACE FOR 10BASET
MB86961APF-G 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:UNIVERSAL INTERFACE FOR 10BASET
MB86965 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:EtherCoupler ETHERNET CONTROLLER WITH 10BASE?T TRANSCEIVER
MB86965B 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:EtherCoupler ETHERNET CONTROLLER WITH 10BASE?T TRANSCEIVER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*