- 您現在的位置：買賣IC網 > PDF目錄67763 > M37920F8CHP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | M37920F8CHP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件頁數： | 8/155頁 |
| 文件大?。?/td> | 1274K |
| 代理商： | M37920F8CHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁
105
M37920F8CGP, M37920F8CHP, M37920FCCGP
M37920FCCHP, M37920FGCGP, M37920FGCHP
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
MITSUBISHI MICROCOMPUTERS
Stop and Wait mode
The stop (hereafter called STP) and the wait (hereafter called WIT)
modes are used to save the power dissipation of the system, by
stopping oscillation or system clock in the case that the CPU needs
not be operating.
The microcomputer enters the STP or WIT mode by executing the
STP or WIT instruction, and either mode is terminated by acceptance
of an interrupt request or reset.
To terminate the STP or WIT mode by an interrupt request, the inter-
rupt to be used for termination of the STP or WIT mode must be en-
abled in advance to execution of the STP or WIT instruction. The
interrupt priority level of this interrupt is required to be higher than the
processor interrupt priority level (IPL) of the routine where the STP
or WIT instruction will be executed.
Figures 102 and 103 show the bit configurations of the particular
function select registers 0, 1. Setting the STP instruction invalidity
select bit (bit 0 of the particular function select register 0) to “1” invali-
dates the STP instruction, and the STP instruction will be ignored.
After reset is removed, since the above bit is cleared to “0”, however,
the STP instruction is valid.
The STP- or the WIT-instruction-execution status bit (bit 0 or 1 of the
particular function select register 1) is set to “1” by the execution of
the STP or the WIT instruction, and so, after the STP or WIT mode
has been terminated, each bit will indicate that the STP or WIT in-
struction has been executed. Accordingly, each of these bits must be
cleared to “0” by software at termination of the STP or the WIT mode.
Table 23 lists the microcomputer’s operation in the STP and WIT
modes.
STP mode
The execution of the STP instruction stops the oscillation circuit. It
also stops clock source
φ, φ1, φBIU, φCPU, and divide clocks f1(φ) to
f4096, Wf32 and Wf512 in the “L” state. In the watchdog timer, “FFF16”
is automatically set, and regardless the contents of watchdog timer
frequency select bit (bit 0 at address 6116), the count source of the
watchdog timer becomes Wf32. This setting is terminated by clear-
ance of the most significant bit of the watchdog timer or reset, and
the count source is back to the one which was selected with the
watchdog timer frequency select bit.
In the STP mode, the A-D converter, DMA controller, DRAM control-
ler (Reflesh timer is also stopped.), and watchdog timer, which use
divide clocks f1(
φ) to f4096, Wf32 and Wf512, are stopped. At this time,
timers A and B operate only in the event counter mode, and serial
I/O communication is active only while an external clock is selected.
The STP mode is terminated by acceptance of an interrupt request
or reset, and the oscillation restarts. Supply of clock source
φ, φ1, di-
vide clocks f1(
φ) to f4096, Wf32 and Wf512 is also restarted.
When the oscillation is restarted by the interrupt request acceptance,
φBIU and φCPU are stopped at “L” level until the most significant bit of
the watchdog timer, which is counted down with divide clock Wf32, is
cleared to “0”. Note that, when the oscillation is restarted, supply of
φBIU and φCPU starts immediately after the oscillation restarts. There-
fore, the reset input must be raised to “H” after the enough oscilla-
tion-stabilizing time has elapsed.
The system where a stable clock is input from the external to pin XIN
is equipped with the mode where an instruction can be executed
immediately after the STP mode termination. For details, refer to the
section on “Stop of oscillation circuit” of the power saving function.
WIT mode
When the WIT instruction is executed with the internal clock stop se-
lect bit at WIT (bit 3 of the particular function select register 1 in Fig-
ure 103) = “0”,
φBIU, φCPU, and divide clocks Wf32 and Wf512 are
stopped in the “L“ state. However, the oscillation circuit, clock source
φ, φ1, and divide clocks f1(φ) to f4096 remain operating. Therefore,
BIU, CPU, and DMA controller are stopped, whereas timers A and B,
serial I/O, and the A-D converter, which use the divide clocks f1(
φ) to
f4096, are still operating. Because the reflesh timer of the DRAM con-
Instruction
WIT
Internal clock
stop select bit
at WIT
Active
Oscillation
circuit
Operations in WIT and STP modes
“0”
φ, φ1,
f1(
φ) to f4096
Active
STP
Wf32, Wf512
φBIU, φCPU
Stopped
(“L”)
Stopped
(“L”)
Peripheral devices using f1(
φ) to f4096, Wf32, Wf512
Timers A, B, Serial I/O, A-D converter: Operation is enabled.
DRAM controller: Reflesh timer is operated.
DMA controller: Stopped. (Watchdog timer: Stopped.)
Timers A, B: Operation is enabled only in the event counter mode.
Serial I/O: Operation is enabled only while an external clock is
selected.
A-D converter, DMA controller: Stopped.
DRAM controller: Reflesh timer is operated.
(Watchdog timer: Stopped.)
Stopped
(“L”)
Stopped
(“L”)
Stopped
(“L”)
Active
“1”
Stopped
(“L”)
Stopped
(“L”)
Stopped
(“L”)
Stopped
Timers A, B: Operation is enabled only in the event counter mode.
Serial I/O: Operation is enabled only while an external clock is
selected.
A-D converter, DMA controller: Stopped.
DRAM controller: Stopped. (Reflesh timer is also stopped.)
(Watchdog timer: Stopped.)
—
Table 23. Microcomputer’s operation in STP and WIT modes
相關PDF資料 |
PDF描述 |
|---|---|
| M37920F8CGP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| M38039MFL-XXXHP | 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PQFP64 |
| M38039MFL-XXXSP | 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PDIP64 |
| M38039MFL-XXXWG | 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PBGA64 |
| M38039FFLHP | 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37920FCCGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
| M37920FCCHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
| M37920FGCGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
| M37920FGCHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
| M37920S4CGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。