- 您現在的位置：買賣IC網 > PDF目錄69010 > M34280E1GP 4-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | M34280E1GP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO20 |
| 封裝： | 0.225 INCH, 0.65 MM PITCH, PLASTIC, SSOP-20 |
| 文件頁數： | 15/48頁 |
| 文件大小： | 605K |
| 代理商： | M34280E1GP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
19
MITSUBISHI MICROCOMPUTERS
4280 Group
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTERS
(4) Return signal
An external wakeup signal is used to return from the RAM
back-up mode. Table 8 shows the return condition for each
return source.
Remarks
Only key-on wakeup function of the port whose pull-down transistor is
turned ON is valid.
Key-on wakeup function is always valid.
Return source
Ports D7, E0, E1
Ports G, E2
Return condition
Return by an external “H” level
input.
Return by an external “H” level
input.
Table 8 Return source and return condition
(5) Pull-down control register PU0
Pull-down control register PU0
Register PU0 controls the ON/OFF of pull-down transistor,
input, key-on wakeup function of ports E0, E1 and D7.
Table 9 Pull-down control register
PU02
PU01
PU00
Pull-down transistor OFF, input circuit OFF, key-on wakeup invalid
Pull-down transistor ON, input circuit ON, key-on wakeup valid
Pull-down transistor OFF, key-on wakeup invalid
Pull-down transistor ON, key-on wakeup valid
Pull-down transistor OFF, key-on wakeup invalid
Pull-down transistor ON, key-on wakeup valid
Port D7 pull-down control bit
Port E1 pull-down control bit
Port E0 pull-down control bit
Pull-down control register PU0
at reset : 0002
at RAM back-up : state retained
W
0
1
0
1
0
1
Note: “W” represents write enabled.
Fig. 21 State transition
Fig. 22 Set source and clear source of the P flag
Fig. 23 Start condition identified example using the SNZP
instruction
S
R
Q
Power down flag P
POF instruction
Reset input
q Set source
POF instruction is executed
q Clear source
Reset input
Software start
P = “1”
?
Yes
Warm start
Cold start
No
Set the contents of this register through register A with the
TPU0A instruction.
: Microcomputer starts its operation after f(XIN) is counted to16384 times.
Stabilizing time a
POF instruction
is executed
A
f(XIN) oscillation
Return input
B
(RAM back-up
mode)
f(XIN) stop
Reset
(Stabilizing time a )
相關PDF資料 |
PDF描述 |
|---|---|
| M34501M2-XXXFP | 4-BIT, MROM, 4.4 MHz, MICROCONTROLLER, PDSO20 |
| M34501E4FP | 4-BIT, OTPROM, 4.4 MHz, MICROCONTROLLER, PDSO20 |
| M34501M2-XXXFP | 4-BIT, MROM, MICROCONTROLLER, PDSO20 |
| M34501E4FP | 4-BIT, OTPROM, MICROCONTROLLER, PDSO20 |
| M34501M4-XXXFP | 4-BIT, MROM, MICROCONTROLLER, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34280M1 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTERS |
| M34280M1-060FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTERS |
| M34280M1-082GP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTERS |
| M34280M1-089FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTERS |
| M34280M1-105FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTERS |
發布緊急采購，3分鐘左右您將得到回復。