- 您現在的位置：買賣IC網 > PDF目錄69009 > M30240M5-XXXFP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M30240M5-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件頁數： | 93/139頁 |
| 文件大?。?/td> | 1453K |
| 代理商： | M30240M5-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁當前第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁
57
Mitsubishi microcomputers
M30240 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Specifications REV. G
Specifications in this manual are tentative and subject to change
Universal Serial Bus
The CPU writes a “1” to this bit to flush the IN FIFO. When there is one packet in the IN FIFO, a flush causes
the IN FIFO to be empty. When there are two packets in the IN FIFO, a flush causes the older packet to be
flushed out from the IN FIFO. Setting the INXCSR6 (FLUSH) bit during transmission could produce unpredict-
able results.
INxCSR7 (AUTO_SET):
When the CPU sets this bit to a “1”, the IN_PKT_RDY bit is set automatically by the USB FCU after the number
of bytes of data equal to the maximum packet size (MAXP) is written into the IN FIFO (see “IN (Transmit)
FIFO” operation for details).
Figure 1.47: USB Endpoint x IN CSR
1.2.18.4.15 USB Endpoint x OUT Control and Status Register
The USB Endpoint x OUT CSR (Control and Status Register), shown in Figure 1.48 contains control and sta-
tus information of the respective OUT Endpoint 1-4.
OUTxCSR0 (OUT_PKT_RDY):
The OUTxCSR0 bit for the OUT FIFO status (see “OUT (Receive) FIFOs” for details).
The USB FCU sets this bit to a “1” and updates the FIFO pointers after a data packet has been successfully
received from the host. The CPU writes a “0” to this bit to inform the USB FCU that a data packet has been
unloaded. The USB FCU updates the FIFO pointers when this occurs. The CPU must allow at least one clock
cycle between writing and reading bit OUTxCSR0.
OUTXxCSR1 (OVER_RUN):
This bit is used in ISO mode only to indicate to the CPU that a FIFO overrun has occurred. The USB FCU sets this
bit to a “1” at the beginning of an OUT token when two data packets are already present in the FIFO. Setting
this bit causes the INST12 bit of the Interrupt Status Register 2 to set. The CPU writes a “0” to clear
OUTXCSR1.
OUTxCSR2 (SEND_STALL):
The CPU writes a “1” to this bit when the endpoint is stalled. The USB FCU returns a STALL handshake while
this bit is set. The CPU writes a “0” to clear this bit.
OUTxCSR3 (ISO/TOGGLE_INIT):
When the endpoint is used for isochronous data transfer, the CPU sets this bit to a “1” for the entire duration
of the isochronous transfer. With the ISO/TOGGLE_INIT bit set to a “1”, the device accepts either DATA0 or
DATA1 for the PID sent by the host.
USB Endpoint x IN Control and Status Register (Note 5)
Symbol
Address
When reset
EPiICS (i= 1-4)
031916, 032116, 032916, 033116
0016
Bit name
Bit symbol
b7
b6
b5
b4
b3
b2
b1
b0
Function
W
R
INxCSR0
INxCSR1
INxCSR2
INxCSR3
INxCSR4
INxCSR5
INxCSR6
INxCSR7
IN_PKT_RDY Bit
UNDER_RUN Flag
SEND_STALL Bit
ISO Bit
INTPT
TX_NOT_EPT Flag
FLUSH Bit
AUTO_SET Bit
0 : Not ready
1 : Ready
0 : No FIFO underrun
1 : FIFO underrun has occured
0 : No action
1 : Stall IN Endpoint x by CPU
0 :
Select non-isochronous transfer
1 : Select isochronous transfer
0 :
Select non-rate feedback interrupt transfer
1 :
Select rate feedback interrupt transfer
0 : Transmit FIFO is empty
1 : Transmit FIFO is not empty
0 : No action
1 : Flush the FIFO
0 : AUTO-SET disabled
1 : AUTO-SET enabled
0
Note 1: Write "1" only or read
Note 2: Write "0" only or read
Note 3: Read only
Note 4: Write only - Read "0"
Note 5: Refer to section 1.5.5 "Programming Notes" for this register
Note 1
Note 2
Note 3
Note 4
相關PDF資料 |
PDF描述 |
|---|---|
| M30240M6-XXXXFP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240ECFP | 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240M5-XXXXFP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240M6-XXXXFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
| M30240ECFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M30240M6 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M6-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M7 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M7-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M8 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。