- 您現在的位置：買賣IC網 > PDF目錄69009 > M30240M5-XXXFP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M30240M5-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件頁數： | 25/139頁 |
| 文件大?。?/td> | 1453K |
| 代理商： | M30240M5-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁
120
Mitsubishi microcomputers
M30240 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Specifications REV. G
Specifications in this manual are tentative and subject to change
Precautions
1.3.1.9 Stop Mode and Wait Mode
When returning from stop mode by hardware reset, RESET pin must be set to “L” level until main clock
oscillation is stabilized.
When entering either wait or stop mode, you must first enable any interrupts you want to cancel the
wait or stop. Also, make sure to disable any interrupts that you don’t want to cancel the wait or stop.
If only hardware reset or NMI interrupts are desired to cancel wait or stop, all other interrupt priority
levels should be set to “0”
If using fSYN as the internal clock, switch it to f(XIN) before entering stop mode.
When switching to either wait or stop mode, the WAIT instruction or the instruction that sets the all
clock stop bit to “1” are prefetched within the instruction queue before the program stops. Put at least
four NOPs in succession after the WAIT instruction or after the instruction that sets the all clock stop
control bit to “1.”
1.3.1.10 Timer A (Timer mode)
Reading the Timer Ai register while a count is in progress allows reading, with arbitrary timing, the val-
ue of the counter. Reading the Timer Ai register with the reload timing gets “FFFF16”. Reading the Tim-
er Ai register after setting a value in the Timer Ai register with a count halted but before the counter
starts counting gets a proper value.
1.3.1.11 Timer A (Event counter mode)
1. Reading the Timer Ai register while a count is in progress allows reading, with arbitrary timing, the
value of the counter. Reading the Timer Ai register with the reload timing gets “FFFF16” by underflow
or “000016” by overflow. Reading the Timer Ai register after setting a value in the Timer Ai register with
a count halted but before the counter starts counting gets a proper value.
2. When counting has stopped in free-run type, set the timer again.
3. When using Free-run type, the timer’s register contents may be undefined when counting starts. Set
the timer value immediately after counting has started.
When the up/down count is not switched:
Enable the reload function and set a value to the timer register before counting starts.
Rewrite the value to the timer register immediately after counting has started. (This is the same operation
as free-run type.)
If counting up, rewrite 000016.
If counting down, rewrite FFFF16.
When the up/down count is switched:
Use the reload type until the first count pulse is input.
Switch to free-run type afterwards.
1.3.1.12 Timer A (One-shot Timer mode)
1. Setting the count start flag to “0” while the count is in progress causes:
The counter to stop counting
The contents of the reload register are reloaded
The TAiOUT pin outputs “L” level
The interrupt request is generated
2. Timer Ai interrupt request bit goes to “1” if the operation mode is set by:
Selecting one-shot timer mode after reset
Changing operation mode from timer mode to one-shot timer mode
Changing operation mode from event counter mode to one-shot timer mode
Note: To use Timer Ai interrupt request bit, clear the Timer Ai interrupt request bit to “0” after these
changes have been made.
相關PDF資料 |
PDF描述 |
|---|---|
| M30240M6-XXXXFP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240ECFP | 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240M5-XXXXFP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240M6-XXXXFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
| M30240ECFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M30240M6 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M6-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M7 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M7-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M8 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。