- 您現在的位置：買賣IC網 > PDF目錄69009 > M30240M5-XXXFP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M30240M5-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件頁數： | 39/139頁 |
| 文件大小： | 1453K |
| 代理商： | M30240M5-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁
133
Mitsubishi microcomputers
M30240 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Specifications REV. G
Specifications in this manual are tentative and subject to change
Frequency Synthesizer
Figure 1.118: PLL and DC-DC Converter Set Up Timing after Hardware Reset
1.5.1.3.1 Precautions after Software Reset
A software reset occurs after writing a ‘1’ to bit ‘3’ of the processor mode register 0 (address 000416). During
software reset, the contents of the internal RAM are preserved as well as all USB, DC-DC converter, and PLL
registers. If the PLL is used as the system clock source, it is important to note that after a software reset oc-
curs, any writes to the frequency synthesizer register will cause it to freeze. This can cause erratic device be-
havior. In order to avoid this, it is recommended that the following procedure be used:
Prior to software reset, switch device clock source from ‘fsyn to f(Xin)’. Please see the Frequency Synthe-
sizer specification for more details.
After software reset using firmware, evaluate the condition of the synthesizer control register (FSC register,
address 03DC16, bit ‘0’). This bit is not effected by a software reset and can check to see if the PLL is still
enabled. If so, any setup routine that involves writing to the PLL registers should not be called. At this point,
the clock source can be changed back to fsyn.
1.5.1.4 Set up after USB Reset Signaling Detected
A USB Reset is detected by the USB FCU when an SE0 is present on D+/D- for at least 2.5
s. De-
tection of a USB Reset results in bit 5 of USB Interrupt Status Register 2 (USBIS2) being set to a “1”
and the registers within the USB FCU being reset to their default values. Register USBC and the PLL
registers are not affected by a USB Reset. A USB Function Interrupt request is also generated when
the USB Reset is detected.
No modifications to the frequency synthesizer or DC-DC converter configuration should be made in
the USB Function Interrupt routine. However, all USB FCU registers (addresses 30016 to 33C16) must
be reconfigured to their pre-enumeration state.
1.5.1.5 Set up after USB Suspend Detected
A USB Suspend occurs if the USB FCU does not detect any bus activity on D+/D- for at least 3 ms.
Detection of a suspend results in bit 7 of USBIS2 and bit 0 of USBPM (SUSPEND) being set to a “1”.
This causes bit 3 of SUSPIC to be set to a “1”. Bit 7 of USBIS2 then needs to be cleared by writing a
“1” to the bit in order to allow a future suspend event.
The configuration of the frequency synthesizer and DC-DC converter should be changed as follows in
the USB Suspend Interrupt routine (if the device is bus powered):
RESET
FSE
LS
USBC4
USBC5
USBC7
Wait 2 ms
Wait (C+1) ms
Enable PLL
Enable DC-DC converter
Enable USB Clock
Enable USB FCU
Wait at least 4 cycles of
Φ
相關PDF資料 |
PDF描述 |
|---|---|
| M30240M6-XXXXFP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240ECFP | 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240M5-XXXXFP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M30240M6-XXXXFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
| M30240ECFP | 16-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M30240M6 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M6-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M7 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M7-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30240M8 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。