- 您現在的位置：買賣IC網 > PDF目錄358968 > LZ85194 (Sharp Corporation) IrDA Control Peripheral Engine(IrDA 控制外圍處理器) PDF資料下載
參數資料
| 型號： | LZ85194 |
| 廠商： | Sharp Corporation |
| 英文描述： | IrDA Control Peripheral Engine(IrDA 控制外圍處理器) |
| 中文描述： | 紅外線控制周邊引擎（紅外線控制外圍處理器） |
| 文件頁數： | 37/76頁 |
| 文件大?。?/td> | 256K |
| 代理商： | LZ85194 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
LZ85194
IrDA Control Peripheral Engine User
’
s Guide
31
Time Limit on Sending Descriptors to USB Dongle via Infrared
The descriptors configured by Set_Peripheral_Info command are sent out to the PC via
infrared and USB after PE
’
s request to μP by its message. At this point, because of the
requirement of USB, the dongle must return USB descriptor from the peripheral to the PC
within 500 ms after receipt of an inquiry from the PC.
Because of this requirement, the dongle will continue its polling with request for the
descriptors to the peripheral devices for the period of approximately 300 ms over infrared,
considering the time required for the overhead as well as polling.
This means, the series of procedure, in which PE signal line MSG to be MSG = H and
obtain message by Get_Message command and then proceed Set_Peripheral_Info when
the message is a request for the descriptor, must be completed within 300 ms.
IrDA-Control Keyboard Sample Flowchart with PE
INITIALIZATION
1. Set SCK to SCK = H
2. Activate PE (by negating RESETB to H level)
3. Wait for MSG becomes MSG = H level
4. Issue
Get_Message
command
5. Issue
Set_Peripheral_Info
, and set the Peripheral
Specific Information (PFID and Peripheral Info)
6. Issue
Set_DcBias
, and enable DC BIAS mode, if
desired.
MAIN ROUTINE
While (1) {
/* Message should be handled with HIGHER Priority*/
/* (such as interrupt) */
If (Key is pressed) { /* Interrupt may be alright*/
do
issue
Send_Data withAck
while (got Ack or TimeOut);
}
If (Enum-button is pressed) { /* Interrupt may be alright*/
issue
Manual_Enum_withBinding
}
}/*end of main loop*/
MESSAGE HANDLING ROUTINE
If (MSG becomes H level) {
issue
Get_Message
and follow the Message instruction
(ex. issue Set_Peripheral_Info, etc.)
Interrupt
85194-13
相關PDF資料 |
PDF描述 |
|---|---|
| LZ8519X | IrDA Control Peripheral Engine (PE) |
| LZ85202 | IrDA Control Host Controller with USB Interface(帶USB接口的IrDA控制主控制器) |
| LZ8520X | IrDA-Control Single-Chip Host Controller (HC) |
| LZ93B53 | Synchronous Signal Generator for CCD |
| LZ93BE0 | Timing Pulse Generator LSI for CCD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LZ8519X | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:IrDA Control Peripheral Engine (PE) |
| LZ85202 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| LZ8520X | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:IrDA-Control Single-Chip Host Controller (HC) |
| LZ87010 | 制造商:Sharp Microelectronics Corporation 功能描述:LZ87010 - Tape and Reel |
| LZ8V2 | 制造商:YEASHIN 制造商全稱:YEASHIN 功能描述:500 mW LL-34 Hermetically Sealed Glass Zener Voltage Regulators |
發布緊急采購，3分鐘左右您將得到回復。