- 您現在的位置：買賣IC網 > PDF目錄358968 > LZ85194 (Sharp Corporation) IrDA Control Peripheral Engine(IrDA 控制外圍處理器) PDF資料下載
參數資料
| 型號： | LZ85194 |
| 廠商： | Sharp Corporation |
| 英文描述： | IrDA Control Peripheral Engine(IrDA 控制外圍處理器) |
| 中文描述： | 紅外線控制周邊引擎（紅外線控制外圍處理器） |
| 文件頁數： | 26/76頁 |
| 文件大小： | 256K |
| 代理商： | LZ85194 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
LZ85194
20
IrDA Control Peripheral Engine User
’
s Guide
Reset Command
Command ID:
0x00
Description:
PE Operation:
PE to configure IrDA Control communication status to Unenumerated
status.
PE to delete the holding Host device information.
Mode bit of PE (Get_OperationMode, Set_OperationMode) is reset to its
default value. Refer to the Table 8 for Mode bits. DC BIAS configuration
will also be disabled status.
Any status of PE is reset to the default values.
DC BIAS mode is not valid after Reset command.
Reset PE to its default configuration
Send_Data Command
Command ID:
0x06
Length:
Byte length resulting from Length + EP + Data. For example, if Data length
is 8 bytes, Length = 10 must be configured. Applicable value is from 2 to 10.
Assign Endpoint for data transmission. For assigning method, Table 6
should be referred.
Transmission Data. Upper end value for N is 11 (MAX. 8 byte data).
Direct PE to send data.
PE Operation:
PE to send data to the assigned Host device.
If PE is in Bound state, PE to send data accordingly.
If PE is in Unbound state, PE to firstly attempt to shift its status to Bound
status, and send data if its attempt succeeded. If failed, it becomes
Unbound again.
If PE is in Unenumerated status, PE to start Enumeration, and will shift
its status to Bound status when successfully Enumerated. If failed, it
stops and remains Unenumerated.
>13.8 ms time gap is required in case of issuing either Send_Data or
Send_Data_withAck after issuing this Command.
There may be a possibility that the data may not be transmitted over IR
link while the buffer is full even though this command is issued. This is
because that this command does not perform the handshake (while
Send_Data_withAck does). For the guaranteed date delivery, use of
Send_Data_withAck is recommended.
EP:
Data:
Description:
1st Byte
Command ID
1st Byte
2nd Byte
3rd Byte
4th - Nth Byte
Command ID
Length
EP
Data
相關PDF資料 |
PDF描述 |
|---|---|
| LZ8519X | IrDA Control Peripheral Engine (PE) |
| LZ85202 | IrDA Control Host Controller with USB Interface(帶USB接口的IrDA控制主控制器) |
| LZ8520X | IrDA-Control Single-Chip Host Controller (HC) |
| LZ93B53 | Synchronous Signal Generator for CCD |
| LZ93BE0 | Timing Pulse Generator LSI for CCD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LZ8519X | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:IrDA Control Peripheral Engine (PE) |
| LZ85202 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| LZ8520X | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:IrDA-Control Single-Chip Host Controller (HC) |
| LZ87010 | 制造商:Sharp Microelectronics Corporation 功能描述:LZ87010 - Tape and Reel |
| LZ8V2 | 制造商:YEASHIN 制造商全稱:YEASHIN 功能描述:500 mW LL-34 Hermetically Sealed Glass Zener Voltage Regulators |
發布緊急采購，3分鐘左右您將得到回復。