- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4268IDKD-1#PBF (Linear Technology)IC PD HIGH POWER W/CNTRL 32-DFN Datasheet資料下載
參數資料
| 型號： | LTC4268IDKD-1#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 41/46頁 |
| 文件大?。?/td> | 419K |
| 描述： | IC PD HIGH POWER W/CNTRL 32-DFN |
| 產品培訓模塊： | Power over Ethernet |
| 標準包裝： | 52 |
| 類型： | 以太網供電開關（PoE） |
| 應用： | 遠程外設（工業控制，相機，數據訪問） |
| 內部開關： | 是 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 32-DFN（7x4）裸露焊盤 |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁
42681fc
LTC4268-1
41
Most capacitor ripple current ratings are based on 2000
hour life. This makes it advisable to derate the capacitor
or to choose a capacitor rated at a higher temperature
than required.
One way to reduce cost and improve output ripple is to use
a simple LC filter. Figure 20 shows an example of the filter.
The design of the filter is beyond the scope of this data
sheet. However, as a starting point, use these general
guidelines. Start with a C
OUT
1/4 the size of the nonfilter
solution. Make C1 1/4 of C
OUT
to make the second filter
pole independent of C
OUT
. C1 may be best implemented
with multiple ceramic capacitors. Make L1 smaller than
the output inductance of the transformer. In general, a
0.1礖 filter inductor is sufficient. Add a small ceramic
capacitor (C
OUT2
) for high frequency noise on V
OUT
. For
those interested in more details refer to Second-Stage
LC Filter Design, Ridley, Switching Power Magazine, July
2000 p8-10.
Circuit simulation is a way to optimize output capacitance
and filters, just make sure to include the component
parasitic. LTC SwitcherCAD
?/DIV>
is a terrific free circuit
simulation tool that is available at www.linear.com. Final
optimization of output ripple must be done on a dedicated
PC board. Parasitic inductance due to poor layout can
significantly impact ripple. Refer to the PC Board Layout
section for more details.
ISOLATION
The 802.3 standard requires Ethernet ports to be electrically
isolated from all other conductors that are user accessible.
This includes the metal chassis, other connectors and
any auxiliary power connection. For PDs, there are two
common methods to meet the isolation requirement. If
there will be any user accessible connection to the PD,
then an isolated DC/DC converter is necessary to meet
the isolation requirements. If user connections can be
avoided, then it is possible to meet the safety requirement
by completely enclosing the PD in an insulated housing.
In all PD applications, there should be no user accessible
electrical connections to the LTC4268-1 or support circuitry
other than the RJ-45 port.
LAYOUT CONSIDERATIONS FOR THE LTC4268-1
The LTC4268-1s PD front end is relatively immune to
layout problems. Place C14 (Figure 9) as close as physically
possible to the LTC4268-1. Place the series 10?resistor
close to C14. Excessive parasitic capacitance on the R
CLASS
pin should be avoided. Include a PCB heat sink to which
the exposed pad on the bottom of the package can be
soldered. This heat sink should be electrically connected
to GND. For optimum thermal performance, make the
heat sink as large as possible. Voltages in a PD can be
as large as 57V for PoE applications, so high voltage
layout techniques should be employed. The SHDN pin
should be separated from other high voltage pins, like
V
PORTP
, V
OUT
, to avoid the possibility of leakage shutting
down the LTC4268-1. If not used, tie SHDN to V
PORTN
.
The load capacitor connected between V
PORTP
and V
OUT
of the LTC4268-1 can store significant energy when fully
charged. The design of a PD must ensure that this energy
is not inadvertently dissipated in the LTC4268-1. The
polarity-protection diodes prevent an accidental short
on the cable from causing damage. However if, V
PORTN
is shorted to V
PORTP
inside the PD while capacitor C1
is charged, current will flow through the parasitic body
diode of the internal MOSFET and may cause permanent
damage to the LTC4268-1.
R
LOAD
C
OUT2
1礔
V
OUT
C
OUT
470礔
C1
47礔
?
FROM
SECONDARY
WINDING
L1
0.1礖
42681 F20
+
+
Figure 20. LC Filter
applicaTions inForMaTion
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4274CUHF#PBF | IC CONTROLLER POE 38-QFN |
| LTC4280CUFD#PBF | IC CONTROLLER HOT SWAP QFN-24 |
| LTC4300-1IMS8#TRPBF | IC HOTSWAP 2WIRE BUS BUFFR 8MSOP |
| LTC4300A-2IMS8#TRPBF | IC BUFFER BUS 2WR HOTSWAP 8-MSOP |
| LTC4301IDD | IC BUFFER BUS HOTSWAP 2WR 8DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4268IDKD-1-TR | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Power PD with Synchronous NoOpto Flyback Controller |
| LTC4268IDKD-1-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Power PD with Synchronous NoOpto Flyback Controller |
| LTC4269-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:IEEE 802.3at PD with Synchronous No-Opto Flyback Controller |
| LTC4269-2 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:IEEE 802.3at High Power PD and Synchronous Forward Controller with AUX Support |
| LTC4269CDKD-1#PBF | 功能描述:IC PD/OPTO FLYBACK CTRLR 32-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。