- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4252A-1IMS#TRPBF (Linear Technology)IC CNTRLR HOTSWAP NEGVOLT 10MSOP Datasheet資料下載
參數資料
| 型號： | LTC4252A-1IMS#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 19/36頁 |
| 文件大小： | 328K |
| 描述： | IC CNTRLR HOTSWAP NEGVOLT 10MSOP |
| 標準包裝： | 2,500 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC4252-1/LTC4252-2
LTC4252A-1/LTC4252A-2
19
425212fe
For more information www.linear.com/LTC4252-1
applicaTions inForMaTion
A low impedance short on one card may influence the
behavior of others sharing the same backplane. The initial
glitch and backplane sag as seen in Figure 6 Trace 1, can
rob charge from output capacitors on adjacent cards.
When the faulty card shuts down, current flows in to
refresh the capacitors. If LTC4252s are used by the other
cards, they respond by limiting the inrush current to a
value of 100mV/R
S
. If C
T
is sized correctly, the capacitors
will recharge long before C
T
times out.
POWER GOOD, PWRGD
PWRGD latches low if GATE charges up to within 2.8V of
V
IN
and DRAIN pulls below V
DRNL
during start-up. PWRGD
is reset in UVLO, in a UV condition or if C
T
charges up
to 4V . An overvoltage condition has no effect on PWRGD
status. A 58礎 current pulls this pin high during reset.
Due to voltage transients between the power module and
PWRGD, optoisolation is recommended. This pin provides
sufficent drive for an optocoupler. Figure 19 shows an
alternative NPN configuration with a limiting base resistor
for the PWRGD interface. The module enable input should
have protection from the negative input current.
MOSFET SELECTION
The external MOSFET switch must have adequate safe
operating area (SOA) to handle short-circuit conditions
until TIMER times out. These considerations take prece-
dence over DC current ratings. A MOSFET with adequate
SOA for a given application can always handle the required
current, but the opposite may not be true. Consult the
manufacturers MOSFET data sheet for safe operating
area and effective transient thermal impedance curves.
MOSFET selection is a 3-step process by assuming the
absense of a soft-start capacitor. First, R
S
is calculated
and then the time required to charge the load capacitance
is determined. This timing, along with the maximum
short-circuit current and maximum input voltage defines
an operating point that is checked against the MOSFETs
SOA curve.
To begin a design, first specify the required load current
and Ioad capacitance, I
L
and C
L
. The circuit breaker cur-
rent trip point (V
CB
/R
S
) should be set to accommodate
the maximum load current. Note that maximum input
current to a DC/DC converter is expected at V
SUPPLY(MIN)
.
R
S
is given by:
R
S
=
V
CB(MIN)
I
L(MAX)
(8)
where V
CB(MIN)
= 40mV (45mV for LTC4252A) represents
the guaranteed minimum circuit breaker threshold.
During the initial charging process, the LTC4252 may oper-
ate the MOSFET in current limit, forcing (V
ACL
) between
80mV to 120mV (V
ACL
is 54mV to 66mV for LTC4252A)
across R
S
. The minimum inrush current is given by:
I
INRUSH(MIN)
=
80mV
R
S
(9)
Maximum short-circuit current limit is calculated using
the maximum V
ACL
. This gives
I
SHORTCIRCUIT(MAX)
=
120mV
R
(10)
The TIMER capacitor C
T
must be selected based on the
slowest expected charging rate; otherwise TIMER might
time out before the load capacitor is fully charged. A value
for C
T
is calculated based on the maximum time it takes
the load capacitor to charge. That time is given by:
t
CL(CHARGE)
=
C"V
I
=
C
L
"V
SUPPLY(MAX)
I
INRUSH(MIN)
(11)
The maximum current flowing in the DRAIN pin is given by:
I
DRN(MAX)
=
V
SUPPLY(MAX)
V
DRNCL
R
D
(12)
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4253ACGN#TRPBF | IC HOT SWAP CONTRLR -48V 16-SSOP |
| LTC4257CS8 | IC CTRLR INTFACE PWR/ETHER 8SOIC |
| LTC4260IUH#PBF | IC HOT SWAP CNTRL I2C 32-QFN |
| LTC4261IGN-2#PBF | IC CTRLR HOTSWAP W/ADC 28-SSOP |
| LTC4263IS#TRPBF | IC IEEE 803.2AF CNTRLR 14-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4252A-2 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:–48V Hot Swap Controllers |
| LTC4252A-2CMS | 功能描述:IC CTRLR HOTSWAP NEG VOLT 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4252A-2CMS#PBF | 功能描述:IC CNTRLR HOTSWAP NEGVOLT 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4252A-2CMS#TR | 功能描述:IC CTRLR HOTSWAP NEG VOLT 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC4252A-2CMS#TRPBF | 功能描述:IC CNTRLR HOTSWAP NEGVOLT 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。