- 您現在的位置：買賣IC網 > PDF目錄377765 > LTC1873EG (LINEAR TECHNOLOGY CORP) Quadruple 2-Input Positive-AND Gate 14-TSSOP -40 to 85 PDF資料下載
參數資料
| 型號： | LTC1873EG |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Quadruple 2-Input Positive-AND Gate 14-TSSOP -40 to 85 |
| 中文描述： | 5 A SWITCHING CONTROLLER, 750 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | 0.209 INCH, PLASTIC, SSOP-28 |
| 文件頁數： | 26/32頁 |
| 文件大?。?/td> | 308K |
| 代理商： | LTC1873EG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁
26
LTC1873
pin, which encompasses both reference accuracy and any
op amp offset. This accounts for 1% error at the output
with a 5V input supply. The feedback voltage line regula-
tion spec adds an additional 0.05%/V term that accounts
for change in reference output with change in input supply
voltage. With a 5V supply, the errors contributed by the
LTC1873 itself typically add up to less than 1% DC error at
the output.
At side 2, the output voltage setting resistors (R1 and R
B
in Figure 3) are the other major contributor to DC error. At
a typical 1.xV output voltage, the resistors are of roughly
the same value, which tends to halve their error terms,
improving accuracy. Still, using 1% resistors for R1 and
R
B
will add 1% to the total output error budget, equal to
that of all errors due to the LTC1
87
3 combined. Using 0.1%
resistors in just those two positions can nearly halve the DC
output error for very little additional cost. Side 1 uses the
internal VID network to set the output voltage, and is
specified to be within
±
1.5% of the values shown in
Table 1.
Load Regulation
Load regulation is affected by feedback voltage, feedback
amplifier gain and external ground drops in the feedback
path. Feedback voltage is covered above and is within 1%
over temperature. A full-range load step might require a
10% duty cycle change to keep the output constant,
requiring the COMP pin to move about 100mV. With
amplifier gain at 85dB, this adds up to only a 10
μ
V shift at
FB, negligible compared to the reference accuracy terms.
External ground drops aren’t so negligible. The LTC1873
can sense the positive end of the output voltage by
attaching the feedback resistor directly at the load, but it
cannot do the same with the ground lead. Just 0.001
of
resistance in the ground lead at 10A load will cause a 10mV
error in the output voltage—as much as all the other DC
errors put together. Proper layout becomes essential to
achieving optimum load regulation from the LTC1873.
See the Layout/Troubleshooting section for more infor-
mation. A properly laid out LTC1873 circuit should move
less than a millivolt at the output from zero to full load.
Maximizing Low Load Current Efficiency
Low load current efficiency depends strongly on proper
operation in discontinuous and Burst Mode operations. In
an ideally optimized system, discontinuous mode reduces
conduction losses but not switching losses, since each
power MOSFET still switches on and off once per cycle. In
a typical system, there is additional loss in discontinuous
mode due to a small amount of residual current left in the
inductor when QB turns off. This current gets dissipated
across the body diode of either QT or QB. Some LTC1873
systems lose as much to body diode conduction as they
save in MOSFET conduction. The real efficiency benefit of
discontinuous mode happens when Burst Mode operation
is invoked. At typical power levels, when Burst Mode
operation is activated, gate drive is the dominant loss
term. Burst Mode operation turns off all output switching
for several clock cycles in a row, significantly cutting gate
drive losses. As the load current in Burst Mode operation
falls toward zero, the current drawn by the circuit falls to
the LTC1873’s background quiescent level—about 3mA
per channel.
To maximize low load efficiency, make sure the LTC1873
is allowed to enter discontinuous and Burst Mode opera-
tion as cleanly as possible. FCB must be above its 0.8V
threshold. Minimize ringing at the SW node so that the
discontinuous comparator leaves as little residual current
in the inductor as possible when QB turns off. It helps to
connect the SW pin of the LTC1873 as close to the drain
of QB as possible. An RC snubber network can also be
added from SW to PGND.
REGULATION OVER COMPONENT TOLERANCE/
TEMPERATURE
DC Regulation Accuracy
The LTC1873 initial DC output accuracy depends mainly
on internal reference accuracy, op amp offset and external
resistor accuracy (side 2 only). Two LTC1873 specs come
into play: feedback voltage and feedback voltage line
regulation. The feedback voltage spec is 800mV
±
8mV
over the full temperature range, and is specified at the FB
APPLICATIOU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1873 | Dual 550kHz Synchronous 2-Phase Switching Regulator Controller with 5-Bit VID(550kHz,雙 路,同步2相開關穩壓器(帶5位VID)) |
| LTC1874 | Dual Constant Frequency Current Mode Step-Down DC/DC Controller(雙路(3.3V,1.8V輸出）恒定頻率，電流模式，步降DC/DC控制器) |
| LTC1874EGN | Quadruple 2-Input Positive-AND Gate 14-VQFN -40 to 85 |
| LTC1875 | 15mA Quiescent Current 1.5A Monolithic Synchronous Step-Down Regulator |
| LTC1875EGN | 15mA Quiescent Current 1.5A Monolithic Synchronous Step-Down Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1873EG#PBF | 功能描述:IC REG CTRLR BUCK PWM VM 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1873EG#TR | 功能描述:IC REG CTRLR BUCK PWM VM 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1873EG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM VM 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1874EGN | 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1874EGN#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。