- 您現在的位置：買賣IC網 > PDF目錄377765 > LTC1873EG (LINEAR TECHNOLOGY CORP) Quadruple 2-Input Positive-AND Gate 14-TSSOP -40 to 85 PDF資料下載
參數資料
| 型號： | LTC1873EG |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Quadruple 2-Input Positive-AND Gate 14-TSSOP -40 to 85 |
| 中文描述： | 5 A SWITCHING CONTROLLER, 750 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | 0.209 INCH, PLASTIC, SSOP-28 |
| 文件頁數： | 24/32頁 |
| 文件大?。?/td> | 308K |
| 代理商： | LTC1873EG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
24
LTC1873
Accuracy Trade-Offs
The V
DS
sensing scheme used in the LTC1873 is not
particularly accurate, primarily due to uncertainty in the
R
DS(ON)
from MOSFET to MOSFET. A second error term
arises from the ringing present at the SW pin, which
causes the V
DS
to look larger than (I
LOAD
)(R
DS(ON)
) at the
beginning of QB’s on-time. These inaccuracies do not
prevent the LTC1873 current limit circuit from protecting
itself and the load from damaging overcurrent conditions,
but they do prevent the user from setting the current limit
to a tight tolerance if more than one copy of the circuit is
being built. The 50% factor in the current setting equation
above reflects the margin necessary to ensure that the
circuit will stay out of current limit at the maximum normal
load, even with a hot MOSFET that is running quite a bit
higher than its R
DS(ON)
spec.
FCB OPERATION/SECONDARY WINDINGS
The FCB pin can be used in conjunction with a secondary
winding on one side of the LTC1873 to generate a third
regulated voltage output. This output can be directly
regulated at the FCB pin. In theory, a fourth output could
be added, either unregulated or with additional external
circuitry at the FCB pin.
The extra auxiliary output is taken from a second winding
on the core of the inductor on one channel, converting it
into a transformer (Figure 13). The auxiliary output voltage
is set by the main output voltage and the turns ratio of the
extra winding to the primary winding. Load regulation at
the auxiliary output will be relatively good as long as the
main output is running in continuous mode. As the load on
the main channel drops and the LTC1873 switches to
discontinuous or Burst Mode operation, the auxiliary
output will not be able to maintain regulation, especially if
the load at the auxiliary output remains heavy.
To avoid this, the auxiliary output voltage is divided down
with a conventional feedback resistor string with the
divided auxiliary output voltage fed back to the FCB pin
(Figure 13). The FCB pin threshold is trimmed to 800mV
CURRENT LIMIT PROGRAMMING
Programming the current limit on the LTC1873 is straight-
forward. The I
MAX
pin sets the current limit by setting the
maximum allowable voltage drop across QB (the bottom
MOSFET) before the current limit circuit engages. The
voltage across QB is set by its on-resistance and the
current flowing in the inductor, which is the same as the
output current. The LTC1873 current limit circuit inverts
the voltage at I
MAX
before comparing it with the negative
voltage across QB, allowing the current limit to be set with
a positive voltage.
To set the current limit, calculate the expected voltage
drop across QB at the maximum desired current:
)
(
I
LIM
should be chosen to be quite a bit higher than the
expected operating current, to allow for MOSFET R
DS(ON)
changes with temperature. Setting I
LIM
to 150% of the
maximum normal operating current is usually safe and will
adequately protect the power components if they are
chosen properly. The 100mV term is an approximate
factor that corrects for errors caused by ringing on the
switch node (illustrated in Figure 6). This factor will
change depending on the layout and the components
used, but 100mV is usually a good starting point. V
DROP
is
then programmed at the I
MAX
pin using the internal 10
μ
A
pull-up and an external resistor:
R
ILIM
= V
PROG
/10
μ
A
The resulting value of R
ILIM
should be checked in an actual
circuit to ensure that the I
LIM
circuit kicks in as expected.
MOSFET R
DS(ON)
specs are like horsepower ratings in
automobiles, and should be taken with a grain of salt.
Circuits that use very low values for R
IMAX
(<20k) should
be checked carefully, since small changes in R
IMAX
can
cause large I
LIM
changes when the 100mV correction
factor makes up a large percentage of the total V
PROG
value. If V
PROG
is set too low, the LTC1873 may fail to
start up.
V
I
R
mV
PROG
ILIM
DS ON
(
=
(
)
+
)
100
APPLICATIOU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1873 | Dual 550kHz Synchronous 2-Phase Switching Regulator Controller with 5-Bit VID(550kHz,雙 路,同步2相開關穩壓器(帶5位VID)) |
| LTC1874 | Dual Constant Frequency Current Mode Step-Down DC/DC Controller(雙路(3.3V,1.8V輸出）恒定頻率，電流模式，步降DC/DC控制器) |
| LTC1874EGN | Quadruple 2-Input Positive-AND Gate 14-VQFN -40 to 85 |
| LTC1875 | 15mA Quiescent Current 1.5A Monolithic Synchronous Step-Down Regulator |
| LTC1875EGN | 15mA Quiescent Current 1.5A Monolithic Synchronous Step-Down Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1873EG#PBF | 功能描述:IC REG CTRLR BUCK PWM VM 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1873EG#TR | 功能描述:IC REG CTRLR BUCK PWM VM 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1873EG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM VM 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1874EGN | 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1874EGN#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。