- 您現在的位置：買賣IC網 > PDF目錄358809 > LM1253AN (NATIONAL SEMICONDUCTOR CORP) Monolithic Triple 180 MHz I2C CRT Pre-amp With Integrated Analog On Screen Display (OSD) Generator PDF資料下載
參數資料
| 型號： | LM1253AN |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 畫面疊加 |
| 英文描述： | Monolithic Triple 180 MHz I2C CRT Pre-amp With Integrated Analog On Screen Display (OSD) Generator |
| 中文描述： | ON-SCREEN DISPLAY IC, PDIP28 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-28 |
| 文件頁數： | 19/57頁 |
| 文件大?。?/td> | 1621K |
| 代理商： | LM1253AN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
Pre-Amp Functional Description
(Continued)
Active Video Transfer Characteristic
Gain, contrast, and DC Offset control the amplitude of the
active video. The Contrast Control range is 20 dB (10X) and
the Gain Control range is 10 dB (3.2X). The DC offset can
vary the active video output level by about 470 mV in total,
allowing a total range of adjustment of about 24V in seven
3.4V steps at the output of a typical LM2453 CRT driver.
OSD Transfer Characteristic
Gain, DC Offset, and OSD Contrast control the amplitude of
the OSD signal. The OSD is not affected by the Brightness
control, but is proportional to the Gain control, with a gain
control range of 10 dB (3.2X). The DC offset will affect the
OSD output level by 470 mV in total. The OSD Contrast will
change the amplitude of the OSD output level by 610 mV in
total.
Brightness/Bias Transfer Characteristic
Bias, Brightness, Gain, and Pedestal control the amplitude
of the brightness/bias (clamp) portion of the signal. The bias
control range sets the brightness/bias pulse between 0.12V
and 0.55V below the value of V
during blanking. The bias
voltage is unaffected by changes in the other controls. The
brightness control is bi-directional and adds or subtracts an
additional amount of between –0.2V and +0.2V to the
brightness/bias pulse during blanking, when gain is set to
maximum. If gain is reduced, the brightness output voltage is
reduced in proportion to allow gain tracking of the brightness
control. The Pedestal controls the offset to the brightness
control, in order that bi-directional operation of the bright-
ness control is always possible at all bias voltage settings.
Auto Beam Limit Control
The Auto Beam Limit control reduces the gain of the video
amplifier in response to a control voltage proportional to the
CRT beam current. It is not recommended that this input be
used as an analog contrast control.
Horizontal Phase Locked Loop
A phase locked oscillator produces a pixel clock for the OSD
generator. This oscillator takes the HBLANK signal as the
sync signal.Aprogrammable divider sets the divide ratio and
thus the number of pixels on a horizontal line.
Fault Operation
Loss of Vertical Flyback Pulse
Loss of vertical flyback pulse implies that the monitor is not
scanning, and therefore no image is being displayed. The
VBLANK pulses are still required by the LM2453 CRT driver
in order to maintain correct bias conditions in the CRT until
the power supplies are switched off, but video is set at black
level.
Note also that interlace mode is supported by the LM1253A.
In interlace mode, a frame is composed of two sequential
fields. In the first field, the odd lines are displayed. In the sec-
ond field the even lines are displayed.Acomplete frame con-
sists of an odd number of horizontal lines, so that each field
contains a half line. This will result in an alternate half line
phase difference between each field of the VFLYBACK pulse
with respect to the HBLANK pulse.
Loss of Horizontal Flyback
Loss of horizontal flyback pulse implies that the monitor is
not scanning, and therefore no image is being displayed.
The HBLANK pulse is still required by the LM2453 CRT
driver in order to maintain correct bias conditions in the CRT
until the power supplies are switched off, but video is set at
black level.
In the absence of an externally supplied horizontal flyback
pulse, the PLL will free run and generate its own HBLANK
pulse. The PLL free run pulse will be gated into the HBLANK
line to the pre-amp to allow normal operation of the pre-amp
and driver biasing.
V
CC
Detect
The V
power supply will be continuously monitored by the
LM1253A. Should the V
supply drop to less than V
CCDET
then the video signal will be set to V
REF
.
The device will continue to operate down to V
, al-
though some parameters may fall outside of specification
when the supply drops below V
CCMIN
.
Power Save Mode
Procedure To Put The LM1253A Into Power Save Mode
or Power Off Blanking
If the monitor has a power save mode the following proce-
dure should be used to put the LM1253A into power save
mode. This should be used for both power save modes initi-
ated from the video card and power save modes initiated by
a user on the front panel of the monitor.
1.
Set Bias and Brightness registers (8434h – 8437h) to 0.
2.
Set the LM1253A to blank video by setting register
8439h to 01h.
3.
Turn off the 8V and 80V supply to the LM2453.
4.
Set the LM1253A to power save by setting register
8439h to 02h.
L
www.national.com
19
相關PDF資料 |
PDF描述 |
|---|---|
| LM1253A | Monolithic Triple 180 MHz I2C CRT Pre-amp With Integrated Analog On Screen Display (OSD) Generator |
| LM1262 | 200 MHz I2C Compatible RGB Video Amplifier System with OSD and DACs |
| LM1262NA | 200 MHz I2C Compatible RGB Video Amplifier System with OSD and DACs |
| LM1267NA | 150 MHz I2C Compatible RGB Video Amplifier System with OSD and DACs |
| LM1267 | 150 MHz I2C Compatible RGB Video Amplifier System with OSD and DACs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM-1256 | 制造商:ROHM 制造商全稱:Rohm 功能描述:16 x 16 matrix displays |
| LM-1256_1 | 制造商:ROHM 制造商全稱:Rohm 功能描述:16】16 matrix displays |
| LM-1256LB1 | 制造商:ROHM 制造商全稱:Rohm 功能描述:16】16 matrix displays |
| LM125AN | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:VOLTAGE REGULATORS |
| LM125H | 制造商: 功能描述: 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。