參數資料
型號: LAN91C96IQFP
廠商: STANDARD MICROSYSTEMS CORP
元件分類: 微控制器/微處理器
英文描述: NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
中文描述: 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP100
封裝: QFP-100
文件頁數: 81/110頁
文件大小: 655K
代理商: LAN91C96IQFP
Non-PCI Single-Chip Full Duplex Ethernet Controller
SMSC DS – LAN91C96I
Page 81
Rev.
11/18/2004
DATASHEET
Squelch Function
The integrated smart squelch circuit employs a combination of amplitude and timing measurements to
determine the validity of data received off the network. It prevents noise at the differential inputs from
falsely triggering the decoder in the absence of valid data or link test pulses. Signal levels below 300mV
(180mV for AUI) or pulse widths less than 15ns at the differential inputs are rejected. Signals above
585mV (300mV for AUI) and pulse widths greater than 30ns will be accepted. When using the extended
cable mode with 10BASE-T media which extends beyond the standard limit of 100 meters, the squelch
level can optionally be set to reject signals below 180mV and accept signals above 300mV. If the input
signal exceeds the squelch requirements, the carrier sense output, nCRS, is asserted.
Reverse Polarity Function
In the 10BASE-T mode, the PHY monitors for receiver polarity reversal due to crossed wires and corrects
by reversing the signal internally.
Collision Detection Function
In the 10BASE-T mode, a collision state is indicated when there are simultaneous transmissions and
receptions on the twisted pair link. During a collision state, the nCOLL signal is asserted. If the received
data ends and the transmit control signal is still active, the transmit data is sent to the MAC within 9 bit
times. The nCOLL signal is de-asserted within 9 bit times after the collision terminates. In the AUI mode,
the external transceiver sends a 10MHz signal to the PHY upon detection of a collision.
Link Integrity
The PHY test for a faulty twisted-pair link. In the absence of transmit data, link test pulses are transmitted
every 16+/-8ms after the end of the last transmission or link pulse on the twisted pair medium. If neither
valid data nor link test pulses are received within 10 to 150ms, the link is declared bad and both data
transmission as well as the operational loopback function are disabled. The Link Integrity function can be
disabled for pre-10BASE-T twisted-pair networks.
相關PDF資料
PDF描述
LAN91C96ITQFP NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
LANF72351D ETHERNET 10BASE-T LAN FILTER MODULES
LANF7236G ETHERNET 10BASE-T LAN FILTER MODULES
LANF72761 ETHERNET 10BASE-T PCMCIA TRANSFORMER MODULES
LANF7307 ETHERNET 10BASE-T LAN FILTER MODULES
相關代理商/技術參數
參數描述
LAN91C96ITQFP 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96-MS 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96-MU 功能描述:以太網 IC Ethernet IC 10Mbps MAC PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96QFP 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96TQFP 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray