參數資料
型號： LAN91C96IQFP
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 微控制器/微處理器
英文描述： NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
中文描述： 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP100
封裝： QFP-100
文件頁數： 61/110頁
文件大小： 655K
代理商： LAN91C96IQFP
Non-PCI Single-Chip Full Duplex Ethernet Controller
SMSC DS – LAN91C96I
Page 61
Rev.
11/18/2004
DATASHEET
8.1
Typical Flow Of Events For Transmit (Auto Release =0)
S/W DRIVER
MAC SIDE
1 ISSUE ALLOCATE MEMORY FOR TX - N
BYTES - the MMU attempts to allocate N bytes
of RAM.
2 WAIT
FOR
SUCCESSFUL
CODE - Poll until the ALLOC INT bit is set or
enable its mask bit and wait for the interrupt.
The TX packet number is now at the Allocation
Result Register.
3 LOAD TRANSMIT DATA - Copy the TX packet
number into the Packet Number Register. Write
the Pointer Register, then use a block move
operation from the upper layer transmit queue
into the Data Register.
4 ISSUE "ENQUEUE PACKET NUMBER TO TX
FIFO" - This command writes the number
present in the Packet Number Register into the
TX FIFO. The transmission is now enqueued.
No further CPU intervention is needed until a
transmit interrupt is generated.
5
COMPLETION
The enqueued packet will be transferred to the
MAC block as a function of TXENA (nTCR) bit
and of the deferral process (1/2 duplex mode
only) state.
a) Upon transmit completion the first word in
memory is written with the status word. The
packet number is moved from the TX FIFO
into the TX completion FIFO. Interrupt is
generated by the TX completion FIFO being
not empty.
b) f a TX failure occurs on any packets, TX
INT is generated and TXENA is cleared,
transmission sequence stops. The packet
number of the failure packet is presented at
the TX FIFO PORTS Register.
6
7 a) SERVICE INTERRUPT - Read Interrupt
Status Register. If it is a transmit interrupt,
read the TX FIFO Packet Number from the
FIFO Ports Register. Write the packet
number into the Packet Number Register.
The corresponding status word is now
readable from memory. If status word
shows
successful
RELEASE packet number command to free
up the memory used by this packet.
Remove packet number from completion
FIFO by writing TX INT Acknowledge
Register.
b) Option 1) Release the packet.
Option 2) Check the transmit status in the
EPH STATUS Register, write the packet
number of the current packet to the Packet
Number Register, re-enable TXENA, then
go to step 4 to start the TX sequence again.
transmission,
issue
相關PDF資料
PDF描述
LAN91C96ITQFP NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
LANF72351D ETHERNET 10BASE-T LAN FILTER MODULES
LANF7236G ETHERNET 10BASE-T LAN FILTER MODULES
LANF72761 ETHERNET 10BASE-T PCMCIA TRANSFORMER MODULES
LANF7307 ETHERNET 10BASE-T LAN FILTER MODULES
相關代理商/技術參數
參數描述
LAN91C96ITQFP 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96-MS 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96-MU 功能描述:以太網 IC Ethernet IC 10Mbps MAC PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96QFP 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96TQFP 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*