- 您現在的位置：買賣IC網 > PDF目錄67754 > L6470PD (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 7 A, PDSO36 PDF資料下載
參數資料
| 型號： | L6470PD |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 7 A, PDSO36 |
| 封裝： | ROHS COMPLIANT, SSOP-36 |
| 文件頁數： | 29/61頁 |
| 文件大小： | 703K |
| 代理商： | L6470PD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
L6470
Programming manual
Doc ID 16737 Rev 1
35/61
9.1.1
ABS_POS
The ABS_POS register contains the current motor absolute position in agreement to the
selected step mode; the stored value unit is equal to the selected step mode (full, half,
quarter, etc.). The available range is from -221 to +221-1 microsteps.
At power-on the register is initialized to "0" (HOME position).
Any attempt to write to the register when the motor is running causes the command to be
ignored and the NOTPERF_CMD to rise (see paragraph 9.1.22).
9.1.2
EL_POS
The EL_POS register contains the current electrical position of the motor. The two MSbits
indicate the current step and the other bits indicate the current microstep (expressed in
step/128) within the step:
When EL_POS register is written by the user the new electrical position is instantly
imposed. When EL_POS register is written its value must be masked in order to mach with
the step mode selected in STEP_MODE register in order to avoid a wrong microstep value
generation (see paragraph 9.1.19); otherwise the resulting microstep sequence will be
incorrect.
Any attempt to write to the register when the motor is running causes the command to be
ignored and the NOTPERF_CMD to rise (see paragraph 9.1.22).
h18
CONFIG
IC configuration
16
2E88
Internal oscillator,
2MHz OSCOUT clock,
supply voltage compensation
disabled,
overcurrent shutdown enabled,
slew-rate = 290 V/s
PWM frequency = 15.6kHz.
R, WS
h19
STATUS
Status
16
XXXX(2)
High impedance state,
UVLO/Reset flag set.
R
h1A
RESERVED
Reserved address
h1B
RESERVED
Reserved address
1.
R: Readable, WS: writable when motor is stopped, WR: writable when motor is running.
2.
According to startup conditions.
Table 8.
Registers map (continued)
Address
[Hex]
Register name
Register function
Len.
[bit]
Reset
Hex
Reset
Value
Remarks
(1)
Table 9.
EL_POS register
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
STEP
MICROSTEP
相關PDF資料 |
PDF描述 |
|---|---|
| L6566BTR | 0.8 A POWER FACTOR CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO16 |
| L6706 | SWITCHING REGULATOR, QCC40 |
| L6717 | DUAL SWITCHING CONTROLLER, 575 kHz SWITCHING FREQ-MAX, QCC48 |
| L6728HTR | SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO10 |
| L6728H | SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6470PDTR | 功能描述:馬達/運動/點火控制器和驅動器 dSPIN 7.0A 8 - 45 V DMOS Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L64710GC-30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Encoder/Decoder |
| L64710GC-40 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Encoder/Decoder |
| L64710GM-25 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Encoder/Decoder |
| L64710GM-30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Encoder/Decoder |
發布緊急采購，3分鐘左右您將得到回復。