- 您現在的位置：買賣IC網 > PDF目錄1924 > IDT82P2816BBG (IDT, Integrated Device Technology Inc)IC LINE INTERFACE UNIT 416-PBGA PDF資料下載
參數資料
| 型號： | IDT82P2816BBG |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 60/146頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LINE INTERFACE UNIT 416-PBGA |
| 標準包裝： | 5 |
| 功能： | 線路接口單元（LIU） |
| 接口： | E1，J1，T1 |
| 電路數： | 1 |
| 電源電壓： | 1.8V, 3.3V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 416-BGA |
| 供應商設備封裝： | 416-PBGA（27x27） |
| 包裝： | 托盤 |
| 包括： | 缺陷和警報檢測，驅動器過流檢測和保護，LLOS 檢測，PRBSARB / IB 檢測和生成 |
| 產品目錄頁面： | 1259 (CN2011-ZH PDF) |
| 其它名稱： | 800-1702 82P2816BBG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁
IDT82P2816
16(+1) CHANNEL HIGH-DENSITY T1/E1/J1 LINE INTERFACE UNIT
Pin Description
20
February 6, 2009
OE
Input
AF9
OE: Output Enable
OE enables or disables all Line Drivers globally.
A high level on this pin enables all Line Drivers while a low level on this pin places all Line
Drivers in High-Z state and independent from related register settings.
Note that the functionality of the internal circuit is not affected by OE.
If this pin is not used, it should be tied to VDDIO.
This pin can be used to control the transmit impedance state for Hitless protection applica-
tions. Refer to Section 4.4 Hitless Protection Switching (HPS) Summary for details.
TEHWE
Input
(Pull-Up)
AD10
TEHWE: Hardware T1/J1 or E1 Mode Selection Enable
When this pin is open, the T1/J1 or E1 operation mode is selected by TEHW globally.
When this pin is low, the T1/J1 or E1 operation mode is selected by the T1E1 bit (b0,
CHCF,...) on a per-channel basis.
TEHW
Input
(Pull-Up)
AC10
TEHW: Hardware T1/J1 or E1 Mode Selection
When TEHWE is open, this pin selects the T1/J1 or E1 operation mode globally:
Low - E1 mode;
Open - T1/J1 mode.
When TEHWE is low, the input on this pin is ignored.
GPIO[0]
GPIO[1]
Output / Input
AD9
AC8
GPIO: General Purpose I/O [1:0]
These two pins can be defined as input pins or output pins by the DIR[1:0] bits (b1~0, GPIO)
respectively.
When the pins are input, their polarities are indicated by the LEVEL[1:0] bits (b3~2, GPIO)
respectively.
When the pins are output, their polarities are controlled by the LEVEL[1:0] bits (b3~2, GPIO)
respectively.
RST
Input
AF10
RST: Reset (Active Low)
A low pulse on this pin resets the device. This hardware reset process completes in 2 s max-
imum. Refer to Section 4.1 Reset for an overview on reset options.
MCU Interface
INT
Output
AF18
INT: Interrupt Request
This pin indicates interrupt requests for all unmasked interrupt sources.
The output characteristics (open drain or push-pull internally) and the active level are deter-
mined by the INT_PIN[1:0] bits (b3~2, GCF).
CS
Input
AD18
CS: Chip Select (Active Low)
This pin must be asserted low to enable the microprocessor interface.
A transition from high to low must occur on this pin for each Read/Write operation and CS
should remain low until the operation is over.
P/S
Input
AC16
P/S: Parallel or Serial Microprocessor Interface Select
P/S selects Serial or Parallel microprocessor interface for the device:
GNDD - Serial microprocessor interface.
VDDIO - Parallel microprocessor interface.
Serial microprocessor interface consists of the CS, SCLK, SDI, SDO pins.
Parallel microprocessor interface consists of the CS, INT/MOT, IM, DS/RD, ALE/AS, R/W/WR,
ACK/RDY, D[7:0], A[10:0] pins.
INT/MOT
Input
(Pull-Up)
AD16
INT/MOT: Intel or Motorola Microprocessor Interface Select
In Parallel microprocessor interface, INT/MOT selects Intel or Motorola microprocessor inter-
face for the device:
GNDD - Parallel Motorola microprocessor interface.
Open - Parallel Intel microprocessor interface.
In Serial microprocessor interface, this pin should be left open.
Name
I / O
Pin No.
Description
相關PDF資料 |
PDF描述 |
|---|---|
| IDT82P2821BH | IC LIU T1/J1/E1 21+1CH 640-PBGA |
| IDT82P2828BHG | IC LIU T1/J1/E1 28+1CH 640-PBGA |
| IDT82P2916BFG | IC LIU T1/E1/J1 16CH SH 484BGA |
| IDT82P5088BBG | IC LIU T1/E1/J1 OCTAL 256PBGA |
| IDT82V2041EPPG | IC LIU T1/J1/E1 1CH 44-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82P2821 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:21(+1) Channel High-Density T1/E1/J1 Line Interface Unit |
| IDT82P2821BH | 功能描述:IC LIU T1/J1/E1 21+1CH 640-PBGA RoHS:否 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| IDT82P2821BHG | 功能描述:IC LINE INTERFACE UNIT 640-PBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| IDT82P2828 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:28(+1) Channel High-Density T1/E1/J1 Line Interface Unit |
| IDT82P2828BH | 功能描述:IC LIU T1/J1/E1 28+1CH 640-PBGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。