- 您現在的位置：買賣IC網 > PDF目錄67705 > ICS9248YF-175LF-T 133 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 PDF資料下載
參數資料
| 型號： | ICS9248YF-175LF-T |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 133 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 封裝： | 0.300 INCH, SSOP-48 |
| 文件頁數： | 13/13頁 |
| 文件大小： | 355K |
| 代理商： | ICS9248YF-175LF-T |
9
ICS9248-175
Advance Information
Third party brands and names are the property of their respective owners.
1.
The ICS clock generator is a slave/receiver, I
2C component. It can read back the data stored in the latches for
verification. Read-Back will support Intel PIIX4 "Block-Read" protocol.
2.
The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode)
3.
The input is operating at 3.3V logic levels.
4.
The data byte format is 8 bit bytes.
5.
To simplify the clock generator I
2C interface, the protocol is set to use only "Block-Writes" from the controller. The
bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete byte
has been transferred. The Command code and Byte count shown above must be sent, but the data is ignored for those
two bytes. The data is loaded until a Stop sequence is issued.
6.
At power-on, all registers are set to a default condition, as shown.
General I
2C serial interface information
The information in this section assumes familiarity with I
2C programming.
For more information, contact ICS for an I
2C programming application note.
How to Write:
Controller (host) sends a start bit.
Controller (host) sends the write address D2
(H)
ICS clock will acknowledge
Controller (host) sends a dummy command code
ICS clock will acknowledge
Controller (host) sends a dummy byte count
ICS clock will acknowledge
Controller (host) starts sending first byte (Byte 0)
through byte 6
ICS clock will acknowledge each byte one at a time.
Controller (host) sends a Stop bit
How to Read:
Controller (host) will send start bit.
Controller (host) sends the read address D3
(H)
ICS clock will acknowledge
ICS clock will send the byte count
Controller (host) acknowledges
ICS clock sends first byte (Byte 0) through byte 6
Controller (host) will need to acknowledge each byte
Controller (host) will send a stop bit
Notes:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D2(H)
ACK
Dummy Command Code
ACK
Dummy Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Byte 6
ACK
Stop Bit
How to Write:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D3(H)
ACK
Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Byte 6
ACK
Stop Bit
How to Read:
相關PDF資料 |
PDF描述 |
|---|---|
| ICS9248YF-179LF-T | 166.66 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS9248YF-179-T | 166.66 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS9248YF-179-T | 166.66 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS9248YF-189-T | 133.33 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS9248YF-195-T | 140 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS9248YF-189-T | 制造商:ICS 制造商全稱:ICS 功能描述:AMD - K7⑩ Clock Generator for Mobile System |
| ICS9248YF-195LF-T | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Generator & Integrated Buffers for PENTIUM II/III & K6 |
| ICS9248YF-199-T | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Generator for SIS 735/740 with AMD K7 Processor |
| ICS9248YF-39 | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Generator & Integrated Buffers for PENTIUM/ProTM |
| ICS9248YF-64 | 制造商:ICS 制造商全稱:ICS 功能描述:AMD-K7TM System Clock Chip |
發布緊急采購，3分鐘左右您將得到回復。