參數資料
型號： HT46C63(100QFP)
英文描述： Microcontroller
中文描述： 微控制器
文件頁數： 18/42頁
文件大?。?/td> 362K
代理商： HT46C63(100QFP)
HT46R63/HT46C63
Rev. 1.00
18
September 9, 2002
When the timer/event counter (reading TMRH) is read,
the cl
ock will be blocked to avoid errors. As this may re-
sults in a counting error, this must be taken into consid-
eration by the programmer.
(Label
Function
0~2 Unused bits, read as 0
TE
3
To define the active edge of TMR pin in-
put signal
(0=active on low to high;
1=active on high to low)
TON
4
To enable or disable timer counting
(0=disabled; 1=enabled)
5
Unused bit, read as 0
TM0
TM1
6
7
To define the operating mode
01=Event count mode (external clock)
10=Timer mode (internal clock)
11=Pulse width measurement mode
00=Unused
TMRC register
Input/Output ports
There are 32 bi-directional input/output lines in the mi-
cro-controller, labeled from PA to PD, which are mapped
to the data memory of [12H], [14H], [16H] and [18H], re-
spectively. All of these I/O ports can be used as input
and output operations. For input operation, these ports
are non-latching, that is, the inputs must be ready at the
T2 rising edge of instruction MOV A,[m] (m=12H, 14H,
16H or 18H). For output operation, all the data is latched
and remains unchanged until the output latch is rewrit-
ten.
Each I/O line has its own control register (PAC, PBC,
PCC, PDC) to control the input/output configuration.
With this control register, CMOS output or schmitt trig-
ger input with or without (depends on options) pull-high
resistorstructurescanbereconfigureddynamically(i.e.,
on-the fly) under software control. To function as an in-
put,thecorrespondinglatchofthecontrolregisterhasto
be set as 1 . The pull-high resistor (if the pull-high re-
sistor is enabled) will be exhibited automatically. The in-
putsourcesarealsodependentonthecontrolregister.If
the control register bit is 1 , the input will read the pad
state ( mov and read-modify-write instructions). If the
control register bit is 0 , the contents of the latches will
move to internal data bus ( mov and read-modify-write
instructions). The input paths (pad state or latches) of
read-modify-write instructions are dependent on the
control register bits. For output function, CMOS is the
only configuration. These control registers are mapped
to locations 13H, 15H, 17H and 19H.
After a chip reset, these input/output lines stay at a high
level (pull-high options) or floating state (non-pull-high
options). Each bit of these input/output latches can be
set or cleared by SET [m].i (m=12H, 14H, 16H or 18H)
instructions. Some instructions first input data and then
follow the output operations. For example, SET [m].i
CLR [m].i , CPLA [m] read the entire port states into
theCPU,executethedefinedoperations(bit-operation),
3
( $ 2 ! %
% # & " -
" # $
! % #
> - # $
( $ 2 ! %
9
/
" , > :
$
.
#
$
& - # $
F
G
F
G
F
" #
,
& #
5
#
! -
& # $
" #
,
$
& - # $
0 & %
$ - $ #
$
.
" #
,
$
& - # $
& # $
#
$
& - # $
#
& #
/
/
F
9
" , > :
! , - $ 1 $ " $
#
& -
, $ 5 & 0 *
8
5 & 0 2 *
8
4 .
$ #
! , - $
" .
Input/Output ports
相關PDF資料
PDF描述
HT46R47(18DIP-A) Analog IC
HT46R47(18SOP-A) Analog IC
HT47C10L 8-Bit R-F Type Low Voltage Mask MCU
HT47C10L(44QFP) Microcontroller
HT506 HIGH TEMPERATURE ANALOG MULTIPLEXERS 16-CHANNEL SINGLE / 8-CHANNEL DUAL
相關代理商/技術參數
參數描述
HT46C63-56SSOP-A 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D with LCD Type 8-Bit MCU
HT46C64 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D with LCD Type 8-Bit MCU
HT46C64_11 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D with LCD Type 8-Bit MCU
HT46C65 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D with LCD Type 8-Bit MCU
HT46C65_11 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D with LCD Type 8-Bit MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*