- 您現在的位置：買賣IC網 > PDF目錄375916 > FS7VS-5 (Mitsubishi Electric Corporation) HIGH-SPEED SWITCHING USE PDF資料下載
參數資料
| 型號： | FS7VS-5 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | HIGH-SPEED SWITCHING USE |
| 中文描述： | 高速開關使用 |
| 文件頁數： | 63/91頁 |
| 文件大?。?/td> | 488K |
| 代理商： | FS7VS-5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁當前第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁
PSD9XX Family
PSD935G2
62
9.6.1 Standard JTAG Signals
The JTAG configuration bit (non-volatile) inside the PSD can be set by the user in the
PSDsoft. Once this bit is set and programmed in the PSD, the JTAG pins are dedicated to
JTAG at all times and is in compliance with IEEE 1149.1. After power up the standard
JTAG signals (TDI, TDO TCK and TMS) are inputs, waiting for a serial command from an
external JTAG controller device (such as FlashLink or Automated Test Equipment). When
the enabling command is received from the external JTAG controller, TDO becomes an
output and the JTAG channel is fully functional inside the PSD. The same command that
enables the JTAG channel may optionally enable the two additional JTAG pins, TSTAT
and TERR.
The PSD935G2 supports JTAG ISP commands, but not Boundary Scan. ST
’
s
PSDsoft software tool and FlashLink JTAG programming cable implement these JTAG-ISP
commands.
9.6.2 JTAG Extensions
TSTAT and TERR are two JTAG extension signals enabled by a JTAG command received
over the four standard JTAG pins (TMS, TCK, TDI, and TDO). They are used to speed
programming and erase functions by indicating status on PSD pins instead of
having to scan the status out serially using the standard JTAG channel. See Application
Note 54.
TERR will indicate if an error has occurred when erasing a sector or programming a byte in
Flash memory. This signal will go low (active) when an error condition occurs, and stay
low until a special JTAG command is executed or a chip reset pulse is received after an
“
ISC-DISABLE
”
command.
TSTAT behaves the same as the Rdy/Bsy signal described in section 9.1.1.3. TSTAT will
be high when the PSD935G2 device is in read array mode (Flash memory and Boot Block
contents can be read). TSTAT will be low when Flash memory programming or erase
cycles are in progress, and also when data is being written to the Secondary Flash Block.
TSTAT and TERR can be configured as open-drain type signals with a JTAG command.
9.6.3 Security and Flash Memories Protection
When the security bit is set, the device cannot be read on a device programmer or through
the JTAG Port. When using the JTAG Port, only a full chip erase command is allowed.
All other program/erase/verify commands are blocked. Full chip erase returns the part to a
non-secured blank state. The Security Bit can be set in PSDsoft.
All Flash Memory and Boot sectors can individually be sector protected against erasures.
The sector protect bits can be set in PSDsoft.
The
PSD935G2
Functional
Blocks
(cont.)
相關PDF資料 |
PDF描述 |
|---|---|
| PSD935F3V-15B81 | Configurable Memory System on a Chip for 8-Bit Microcontrollers |
| PSD935F3V-15B81I | Ceramic Chip Capacitors / MIL-PRF-55681; Capacitance [nom]: 30000uF; Working Voltage (Vdc)[max]: 100V; Capacitance Tolerance: +/-0.1pF; Dielectric: Multilayer Ceramic; Temperature Coefficient: C0G (NP0); Lead Style: Surface Mount Chip; Lead Dimensions: 0805; Termination: Solder Coated (Sn/Pb, 70/30); Body Dimensions: 0.080" x 0.050" x 0.055"; Container: Bag; Features: MIL-PRF-55681: S Failure Rate |
| PSD935F3V-15J | Configurable Memory System on a Chip for 8-Bit Microcontrollers |
| PSD935F3V-15JI | Configurable Memory System on a Chip for 8-Bit Microcontrollers |
| PSD935F3V-15M | Configurable Memory System on a Chip for 8-Bit Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FS-8000 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:MULTI-USER KVM SWITCH |
| FS-80-0-300V | 制造商:Fuji Electric 功能描述: |
| FS800R06KE3_H7E | 制造商:Infineon Technologies AG 功能描述: |
| FS800R07A2E3 | 功能描述:IGBT 模塊 IGBT Module 650V 700A RoHS:否 制造商:Infineon Technologies 產品:IGBT Silicon Modules 配置:Dual 集電極—發射極最大電壓 VCEO:600 V 集電極—射極飽和電壓:1.95 V 在25 C的連續集電極電流:230 A 柵極—射極漏泄電流:400 nA 功率耗散:445 W 最大工作溫度:+ 125 C 封裝 / 箱體:34MM 封裝: |
| FS800R07A2E3BOSA2 | 制造商:Infineon Technologies AG 功能描述:Trans IGBT Module N-CH 650V 700A 33-Pin |
發布緊急采購，3分鐘左右您將得到回復。