參數資料
型號： FS7VS-5
廠商： Mitsubishi Electric Corporation
英文描述： HIGH-SPEED SWITCHING USE
中文描述： 高速開關使用
文件頁數： 57/91頁
文件大?。?/td> 488K
代理商： FS7VS-5
PSD9XX Family
PSD935G2
56
The
PSD935G2
Functional
Blocks
(cont.)
Access
5V V
CC
,
Typical
Standby
Current
50 μA
(Note 2)
PLD
Memory
Access
Time
Recovery Time
to Normal
Access
Propagation
Delay
Normal tpd
(Note 1)
Mode
Power Down
No Access
tLVDV
Table 25. PSD935G2 Timing and Standby Current During Power
Down Mode
NOTES:
1. Power Down does not affect the operation of the PLD. The PLD operation in this
mode is based only on the Turbo Bit.
2. Typical current consumption assuming no PLD inputs are changing state and
the PLD Turbo bit is off.
Port Function
MCU I/O
PLD Out
Address Out
Data Port
Peripheral I/O
Pin Level
No Change
No Change
Undefined
Three-State
Three-State
Table 24. Power Down Mode’s Effect on
Ports
9.5.1 Automatic Power Down (APD) Unit and Power Down Mode (cont.)
Power Down Mode
By default, if you enable the PSD APD unit, Power Down Mode is automatically enabled.
The device will enter Power Down Mode if the address strobe (ALE/AS) remains inactive
for fifteen CLKIN (pin PD1) clock periods.
The following should be kept in mind when the PSD is in Power Down Mode:
If the address strobe starts pulsing again, the PSD will return to normal operation.
The PSD will also return to normal operation if either the CSI input returns low or the
Reset input returns high.
The MCU address/data bus is blocked from all memories and PLDs.
Various signals can be blocked (prior to Power Down Mode) from entering the PLDs
by setting the appropriate bits in the PMMR registers. The blocked signals include
MCU control signals and the common clock (CLKIN). Note that blocking CLKIN from
the PLDs will not block CLKIN from the APD unit.
All PSD memories enter Standby Mode and are drawing standby current. However,
the PLDs and I/O ports do
not
go into Standby Mode because you don’t want to
have to wait for the logic and I/O to “wake-up” before their outputs can change. See
Table 24 for Power Down Mode effects on PSD ports.
Typical standby current is 50 μA for 5 V parts. This standby current value assumes
that there are no transitions on any PLD input.
相關PDF資料
PDF描述
PSD935F3V-15B81 Configurable Memory System on a Chip for 8-Bit Microcontrollers
PSD935F3V-15B81I Ceramic Chip Capacitors / MIL-PRF-55681; Capacitance [nom]: 30000uF; Working Voltage (Vdc)[max]: 100V; Capacitance Tolerance: +/-0.1pF; Dielectric: Multilayer Ceramic; Temperature Coefficient: C0G (NP0); Lead Style: Surface Mount Chip; Lead Dimensions: 0805; Termination: Solder Coated (Sn/Pb, 70/30); Body Dimensions: 0.080" x 0.050" x 0.055"; Container: Bag; Features: MIL-PRF-55681: S Failure Rate
PSD935F3V-15J Configurable Memory System on a Chip for 8-Bit Microcontrollers
PSD935F3V-15JI Configurable Memory System on a Chip for 8-Bit Microcontrollers
PSD935F3V-15M Configurable Memory System on a Chip for 8-Bit Microcontrollers
相關代理商/技術參數
參數描述
FS-8000 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:MULTI-USER KVM SWITCH
FS-80-0-300V 制造商:Fuji Electric 功能描述:
FS800R06KE3_H7E 制造商:Infineon Technologies AG 功能描述:
FS800R07A2E3 功能描述:IGBT 模塊 IGBT Module 650V 700A RoHS:否 制造商:Infineon Technologies 產品:IGBT Silicon Modules 配置:Dual 集電極—發射極最大電壓 VCEO:600 V 集電極—射極飽和電壓:1.95 V 在25 C的連續集電極電流:230 A 柵極—射極漏泄電流:400 nA 功率耗散:445 W 最大工作溫度:+ 125 C 封裝 / 箱體:34MM 封裝:
FS800R07A2E3BOSA2 制造商:Infineon Technologies AG 功能描述:Trans IGBT Module N-CH 650V 700A 33-Pin
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*