- 您現在的位置：買賣IC網 > PDF目錄373783 > ZL30105QDG1 (ZARLINK SEMICONDUCTOR INC) T1/E1/SDH Stratum 3 Redundant System Clock Synchronizer for AdvancedTC TM and H.110 PDF資料下載
參數資料
| 型號： | ZL30105QDG1 |
| 廠商： | ZARLINK SEMICONDUCTOR INC |
| 元件分類： | 通信及網絡 |
| 英文描述： | T1/E1/SDH Stratum 3 Redundant System Clock Synchronizer for AdvancedTC TM and H.110 |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, 1 MM HEIGHT, LEAD FREE, MS-026ACD, TQFP-64 |
| 文件頁數： | 30/52頁 |
| 文件大小： | 1097K |
| 代理商： | ZL30105QDG1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
ZL30105
Data Sheet
30
Zarlink Semiconductor Inc.
When the redundant timing card is switched to becoming the active timing card, the system controller should do the
following:
select Primary Master mode, SEC_MSTR=0
select Automatic mode, MODE_SEL1:0=11
The new active timing card will automatically select a valid input reference REF0 or REF1. If both input references
are available and valid, then REF0 will be chosen over REF1. If the new active timing card should use the same
input reference (REF0 or REF1) as the old active timing card used before it failed, The system controller should do
the following instead:
select Holdover (manual) mode, MODE_SEL1:0=01
select Primary Master mode, SEC_MSTR=0
select the required reference (REF0 or REF1) as the input reference
Normal Mode, MODE_SEL1:0=00 (forces device to the input reference set at REF_SEL)
It is recommended to maintain HMS=1 when switching from redundant to active through the Holdover mode, to
eliminate output phase transients.
When the active timing card is switched to becoming the redundant timing card, the system controller should do the
following:
select Normal (manual) mode, MODE_SEL1:0=00
select Secondary Master mode, SEC_MSTR=1
select REF2 and REF2_SYNC as the input reference, REF_SEL1=1
The ZL30105 allows for the switch from Secondary Master mode to Primary Master mode with no frequency or
phase hits on the output clocks. The switch from Primary Master mode to Secondary Master mode may introduce a
phase transient on the output clocks as the TIE correction circuit is disabled to allow the Secondary master device
to track the active clocks closely.
相關PDF資料 |
PDF描述 |
|---|---|
| ZL30105 | Power Clamp On Multimeter; DMM Type:Clamp; No. of Digits/Alpha:3-3/4; DMM Response Type:True RMS; Approval Categories:CAT III 600V; Calibrated:No; Current Measuring Range:0-400.0A; Current Setting AC:400A RoHS Compliant: NA |
| ZL30105QDG | Digital Clamp-On Meter; DMM Type:Clamp; No. of Digits/Alpha:3-3/4; DMM Response Type:True RMS; Calibrated:No; Current Setting AC:1000A; Resistance Measuring Range:400 Ohm to 10 MOhm; Voltage Measuring Range AC:600V RoHS Compliant: NA |
| ZL30106QDG1 | SONET/SDH/PDH Network Interface DPLL |
| ZL30106 | SONET/SDH/PDH Network Interface DPLL |
| ZL30106QDG | SONET/SDH/PDH Network Interface DPLL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ZL30106 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:SONET/SDH/PDH Network Interface DPLL |
| ZL30106_05 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:SONET/SDH/PDH Network Interface DPLL |
| ZL30106QDG | 制造商:Zarlink Semiconductor Inc 功能描述:SONET/SDH/PDH NETWORK INTRFC 64TQFP - Trays 制造商:Microsemi 功能描述:Microsemi ZL30106QDG Communication Misc |
| ZL30106QDG1 | 制造商:Zarlink Semiconductor Inc 功能描述:SONET/SDH/PDH NETWORK INTRFC 64TQFP - Trays 制造商:Zarlink Semiconductor Inc 功能描述:PB FREE SONET/SDH/PDH NTWK INTERFACEDPLL |
| ZL30107 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:GbE Line Card Synchronizer |
發(fā)布緊急采購，3分鐘左右您將得到回復。