- 您現在的位置：買賣IC網 > PDF目錄376983 > DS87C550-FNL EPROM High-Speed Micro with A/D and PWM PDF資料下載
參數資料
| 型號： | DS87C550-FNL |
| 英文描述： | EPROM High-Speed Micro with A/D and PWM |
| 中文描述： | 存儲器高速微與A / D及PWM |
| 文件頁數： | 4/50頁 |
| 文件大?。?/td> | 763K |
| 代理商： | DS87C550-FNL |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
DS87C550
4 of 50
PIN DESCRIPTION
Table 1
PLCC/
CLCC
QFP
2
72
36
37
35
15
9
SIGNAL NAME
V
CC
GND
DESCRIPTION
V
CC
-
Digital +5V power input.
GND –
Digital ground.
34
RST
RST - I/O.
The RST input pin contains a Schmitt voltage input to recognize
external active high Reset inputs. The pin also employs an internal pulldown
resistor to allow for a combination of wired OR external Reset sources. An RC is
not required for power-up, as the DS87C550 provides this function internally.
This pin also acts as an output when the source of the reset is internal to the device
(i.e., watchdog timer, power-fail, or crystal-fail detect). In this case, the RST pin
will be held high while the processor is in a Reset state, and will return to low as
the processor exits this state. When this output capability is used, the RST pin
should not be connected to an RC network or a logic output driver.
Input -
The crystal oscillator pins XTAL1 and XTAL2 provide support for
fundamental mode, parallel resonant, AT cut crystals. XTAL1 acts also as an input
if there is an external clock source in place of a crystal. XTAL2 serves as the
output of the crystal amplifier. Note that this output cannot be used to drive any
additional load when a crystal is attached as this can disturb the oscillator circuit.
35
34
32
31
XTAL1
XTAL2
47
48
PSEN
PSEN
- Output.
The Program Store Enable output. This signal is commonly
connected to optional external ROM memory as a chip enable.
PSEN
will provide
an active low pulse during a program byte access, and is driven high when not
accessing external program memory.
ALE - Output.
The Address Latch Enable output functions as a clock to latch the
external address LSB from the multiplexed address/data bus on Port 0. This signal
is commonly connected to the latch enable of an external 373 family transparent
latch. ALE is driven high when the DS87C550 is in a Reset condition. ALE can
also be disabled and forced high using the EMI reduction mode ALEOFF.
EA
- Input.
An active low input pin that when connected to ground will force the
DS87C550 to use an external program memory. The internal RAM is still
accessible as determined by register settings.
EA
should be connected to V
CC
to
use internal program memory. The input level on this pin is latched at reset.
Port 1 - I/O.
Port 1 functions as both an 8-bit, bi-directional I/O port and an
alternate functional interface for several internal resources. The reset condition of
Port 1 is all bits at logic 1. In this state, a weak pullup holds the port high. This
condition allows the pins to serve as both input and output. Input is possible since
any external circuit whose output drives the port will overcome the weak pullup.
When software writes a 0 to any Port 1 pin, the DS87C550 will activate a strong
pulldown that remains on until either a 1 is written or a reset occurs. Writing a 1
after the port has been at 0 will cause a strong transition driver to turn on, followed
by a weaker sustaining pullup. Once the momentary strong driver turns off, the
port again returns to a weakly held high output (and input) state. The alternate
functions of Port 1 pins are detailed below. Note that when the Capture/Compare
functions of timer 2 are used, the interrupt input pins become capture trigger
inputs.
48
49
ALE
49
50
EA
16-23
10-17
P1.0-P1.7
Port
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
Alternate Function
INT2/CT0 External Interrupt 2/Capture Trigger 0
INT3/CT1 External Interrupt 3/Capture Trigger 1
INT4/CT2 External Interrupt 4/Capture Trigger 2
INT5/CT3 External Interrupt 5/Capture Trigger 3
T2
External I/O for Timer/Counter 2
T2EX
Timer/Counter 2 Capture/Reload Trigger
RXD1
Serial Port 1 Input
TXD1
Serial Port 1 Output
16
17
18
19
20
21
22
23
10
11
12
13
14
15
16
17
相關PDF資料 |
PDF描述 |
|---|---|
| DS87C550-KCL | EPROM High-Speed Micro with A/D and PWM |
| DS87C550-QNL | EPROM High-Speed Micro with A/D and PWM |
| DS8820J | Line Receiver |
| DS8859AJ | LED Display Driver |
| DS8859AN | LED Display Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS87C550-KCL | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:EPROM High-Speed Micro with A/D and PWM |
| DS87C550-QCL | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:EPROM High-Speed Micro with A/D and PWM |
| DS87C550-QCL+ | 功能描述:IC MCU EPROM ADC/PWM HS 68-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:87C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
| DS87C550-QCW | 制造商:Maxim Integrated Products 功能描述:DS87C550 WAIVERED FOR LS & MARKING - Rail/Tube |
| DS87C550-QNL | 功能描述:IC MCU EPROM ADC/PWM HS 68-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:87C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。