- 您現在的位置：買賣IC網 > PDF目錄376983 > DS87C550-FNL EPROM High-Speed Micro with A/D and PWM PDF資料下載
參數資料
| 型號： | DS87C550-FNL |
| 英文描述： | EPROM High-Speed Micro with A/D and PWM |
| 中文描述： | 存儲器高速微與A / D及PWM |
| 文件頁數： | 22/50頁 |
| 文件大?。?/td> | 763K |
| 代理商： | DS87C550-FNL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
DS87C550
22 of 50
Specifications section). This reference voltage may be selected to be either an internal band-gap voltage
(VBG) or an external reference (Avref+, Avref-). This selection is made by writing a 0 (uses internal
reference VBG) or writing a 1 (uses external reference (Avref+, Avref-) to the ADRS bit (PWMADR.7).
The default reset condition is for the internal reference to be selected.
Selecting a single analog signal for conversion is achieved by software writing the desired channel
number (0 through 7) into SFR bits MUX2 through MUX0 bits of the A/D Control Register 2
(ADCON2.6-4). The single output of the multiplexer is then provided to a sample and hold circuit that
maintains a steady signal during the conversion process.
A/D CONVERSION PROCESS
The A/D conversion process can be configured for one-shot or continuous mode operation. For one-shot
operation, the SFR bit CONT/SS (ADCON1.5) must be a 0. The conversion process is then initiated by
software writing a 1 to the STRT/BSY SFR bit (ADCON1.7) if the ADEX (ADCON1.4) bit is a 0. If the
ADEX bit is a 1, then the conversion is initiated by an active low signal on the external pin STADC
(P6.7). If continuous mode is selected (CONT/SS = 1), then the first conversion is initiated as described
above, but another conversion will be automatically started at the completion of the previous conversion.
Once initiated, the conversion process requires 16 A/D clock periods (T
ACLK
) to complete. Because of the
dynamic nature of the converter, the A/D clock period can be no less that 1 us and no more than 6.25 us.
This requirement is expressed as follows:
1.0 us <= T
ACLK
<= 6.25 us
Therefore any single conversion time can range from 16 us minimum to 100 us maximum, depending on
the selected A/D clock frequency.
The A/D clock frequency is a function of the processor’s machine cycle clock and the A/D clock’s
prescaler setting as shown by the following equation:
T
ACLK
= T
MCLK
* (N+1)
where N is the prescaler setting in APS3:0.
The processor’s machine cycle clock period (T
MCLK
) is normally the external crystal (or oscillator)
frequency multiplied by 4 (but can be affected by the CD1, CD0, and 4X/
2X
bits). The A/D clock period
must be set by the user to ensure that it falls within the minimum and maximum values specified above.
As an example, assume the processor’s crystal frequency is 33 MHz and that the processor is running in a
standard divide-by-4 mode. This means that the period of the processors machine cycle clock, i.e.,
T
MCLK
, will be (1/33 MHz)*4 or 121.2 ns. If it is assumed that the application requires the fastest possible
conversion time, then the desired T
ACLK
is 1.0 us. The necessary prescale value can then be calculated as:
N = (T
ACLK
/T
MCLK
)-1
Therefore for this example, N = 7.25. Since N must be an integer, the value of N must be 8 (rounded up
to the next integer). This results in a conversion clock T
ACLK
= 1.091 us.
The prescaler value must be stored in SFR bits APS3 through APS0 (ADCON2.3-0) to achieve the proper
A/D clock. These bits default to 0 on a processor reset, so they must be set as desired by the processor’s
initialization software.
相關PDF資料 |
PDF描述 |
|---|---|
| DS87C550-KCL | EPROM High-Speed Micro with A/D and PWM |
| DS87C550-QNL | EPROM High-Speed Micro with A/D and PWM |
| DS8820J | Line Receiver |
| DS8859AJ | LED Display Driver |
| DS8859AN | LED Display Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS87C550-KCL | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:EPROM High-Speed Micro with A/D and PWM |
| DS87C550-QCL | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:EPROM High-Speed Micro with A/D and PWM |
| DS87C550-QCL+ | 功能描述:IC MCU EPROM ADC/PWM HS 68-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:87C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
| DS87C550-QCW | 制造商:Maxim Integrated Products 功能描述:DS87C550 WAIVERED FOR LS & MARKING - Rail/Tube |
| DS87C550-QNL | 功能描述:IC MCU EPROM ADC/PWM HS 68-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:87C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。