- 您現在的位置：買賣IC網 > PDF目錄376983 > DS87C550-FNL EPROM High-Speed Micro with A/D and PWM PDF資料下載
參數資料
| 型號： | DS87C550-FNL |
| 英文描述： | EPROM High-Speed Micro with A/D and PWM |
| 中文描述： | 存儲器高速微與A / D及PWM |
| 文件頁數： | 14/50頁 |
| 文件大小： | 763K |
| 代理商： | DS87C550-FNL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
DS87C550
14 of 50
Another useful feature of the device is its ability to automatically switch the active data pointer after a
DPTR-based instruction is executed. This feature can greatly reduce the software overhead associated
with data memory block moves, which toggle between the source and destination registers. When the
Toggle Select bit (TSL;DPS.5) is set to 1, the SEL bit (DPS.0) is automatically toggled every time one of
the following DPTR related instructions are executed:
§
INC DPTR
§
MOV DPTR, #data16
§
MOVC A, @A+DPTR
§
MOVX A, @DPTR
§
MOVX @DPTR, A
As a brief example, if TSL is set to 1, then both data pointers can be updated with the two instruction
series shown.
INC DPTR
INC DPTR
With TSL set, the first increment instruction increments the active data pointer, and then causes the SEL
bit to toggle making the other DPTR active. The second increment instruction increments the newly
active data pointer and then toggles SEL to make the original data pointer active again.
CLOCK CONTROL and POWER
MANAGEMENT
The DS87C550 includes a number of unique features that allow flexibility in selecting system clock
sources and operating frequencies. To support the use of inexpensive crystals while allowing full-speed
operation, a clock multiplier is included in the processor’s clock circuit. Also, along with the Idle and
power-down (Stop) modes of the standard 80C52, the DS87C550 provides a new Power Management
mode. This mode allows the processor to continue instruction execution at a very low speed to
significantly reduce power consumption (below even idle mode). The DS87C550 also features several
enhancements to Stop mode that make this extremely low power mode more useful. Each of these
features is discussed in detail below.
SYSTEM CLOCK CONTROL
As mentioned previously, the DS87C550 contains special clock control circuitry that simultaneously
provides maximum timing flexibility and maximum availability and economy in crystal selection. There
are two basic functions to this circuitry: a frequency multiplier and a clock divider. By including a
frequency multiplier circuit, full-speed operation of the processor may be achieved with a lower
frequency crystal. This allows the user the ability to choose a more cost-effective and easily obtainable
crystal than would be possible otherwise.
The logical operation of the system clock divide control function is shown in Figure 3. The clock signal
from the crystal oscillator (or external clock source) is provided to the frequency multiplier module, to a
divide-by-256 module, and to a 3-to-1 multiplexer. The output of this multiplexer is considered the
system clock
. The system clock provides the time base for timers and internal peripherals, and feeds the
CPU State Clock Generation circuitry. This circuitry divides the system clock by 4, and it is the four
phases of this clock that make up the instruction execution clock. The four phases of a single instruction
execution clock are also called a single
machine cycle clock
. Instructions in the DS87C550 all use the
machine cycle as the fundamental unit of measure and are executed in from one to five of these machine
cycles. It is important to note the distinction between the system clock and the machine cycle clock as
they are often confused, creating errors in timing calculations. In performing timing calculations, it is
相關PDF資料 |
PDF描述 |
|---|---|
| DS87C550-KCL | EPROM High-Speed Micro with A/D and PWM |
| DS87C550-QNL | EPROM High-Speed Micro with A/D and PWM |
| DS8820J | Line Receiver |
| DS8859AJ | LED Display Driver |
| DS8859AN | LED Display Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS87C550-KCL | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:EPROM High-Speed Micro with A/D and PWM |
| DS87C550-QCL | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:EPROM High-Speed Micro with A/D and PWM |
| DS87C550-QCL+ | 功能描述:IC MCU EPROM ADC/PWM HS 68-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:87C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
| DS87C550-QCW | 制造商:Maxim Integrated Products 功能描述:DS87C550 WAIVERED FOR LS & MARKING - Rail/Tube |
| DS87C550-QNL | 功能描述:IC MCU EPROM ADC/PWM HS 68-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:87C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。