- 您現在的位置：買賣IC網 > PDF目錄11785 > DS80C411-FNY+ (Maxim Integrated Products)IC MCU 75MHZ 16MB HP 100-LQFP PDF資料下載
參數資料
| 型號： | DS80C411-FNY+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 94/102頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 75MHZ 16MB HP 100-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 90 |
| 系列： | 80C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 75MHz |
| 連通性： | 1 線，CAN，EBI/EMI，以太網，SIO，UART/USART |
| 外圍設備： | 電源故障復位，WDT |
| 輸入/輸出數： | 64 |
| 程序存儲器容量： | 64KB（64K x 8） |
| 程序存儲器類型： | ROM |
| RAM 容量： | 64K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.62 V ~ 3.6 V |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 100-LQFP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁當前第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
DS80C410/DS80C411 Network Microcontrollers with Ethernet and CAN
91 of 102
register, the receive shift register holds the new byte and waits until the user reads the receive buffer, clearing the
RBF flag. Thus, if both RSRF and RBF are set, no further transmissions should be made on the 1-Wire bus, or else
data can be lost, as the byte in the receive shift register is overwritten by the next received data.
To read data from a slave device, the bus master must first be ready to transmit data depending on commands in
the command register already set up by the CPU. Data is retrieved from the bus in a similar fashion to a write
operation. The CPU initiates a read operation by writing FFh data to the transmit buffer. The data that is then
shifted into the receive shift register is the wired-AND of the bus master write data (FFh) and the data from the
slave device. When the receive shift register is full, the data is transferred to the receive buffer (if RBF = 0), where
it can be read by the CPU. Additional bytes can be read by sending FFh again. If the slave device is not ready to
respond to read request, the data received the by the bus master is identical to that which was transmitted (FFh).
Bus Master Commands
The 1-Wire bus master can generate special commands on the 1-Wire bus in addition to transmitting and receiving
data. These commands are generated through the setting of a corresponding bit in the command register
(xxxxx000h). These operational modes are defined in The Book of iButton Standards available on our website at
1WR (Bit 0): 1-Wire Reset. Setting this bit to logic 1 causes a reset of the 1-Wire bus, which must precede any
command given on the bus. Setting this bit also automatically clears the SRA bit. The 1WR bit is automatically
cleared as soon as the 1-Wire bus reset completes. The bus master sets the presence-detect interrupt flag (PD)
when the reset is completed and sufficient time for a 1-Wire reset to occur has passed. The result of the 1-Wire
reset is placed in the interrupt register bit PDR. If a presence-detect pulse was received, PDR is cleared; otherwise,
it is set.
SRA (Bit 1): Search ROM Accelerator. Setting this bit to logic 1 places the bus master into search-ROM-
accelerator mode in order to expedite the search ROM process. The general principle of the search ROM process
is to deselect one device after another at every conflicting ROM ID bit position of the attached slave devices. Using
the search ROM process, the bus master can ultimately learn the ROM ID for each device attached to the 1-Wire
bus. To prevent the CPU from having to perform many bit manipulations during a search ROM process, the search-
ROM-accelerator mode can be invoked, allowing the CPU to send 16 bytes of data to complete a single search
ROM pass. Details about the search ROM algorithm can be found in The Book of iButton Standards or the High-
Speed Microcontroller User’s Guide: Network Microcontroller Supplement.
FOW (Bit 2): Force OW Line Low. Setting this bit to logic 1 forces the OW line to a low value if the EN_FOW bit in
the control register is also set to logic 1. The FOW bit has no affect on the OW line when the EN_FOW bit is
cleared to logic 0.
OW_IN (Bit 3): OW Line Input. This bit always reflects the current logic state of the OW line.
Bus Master Controls
The 1-Wire bus master can perform certain special functions to support OW line operation. These special functions
can be configured through the control register (xxxxx101h).
LLM (Bit 0): Long Line Mode. This bit is used to enable the long-line mode timing. Setting this bit to logic 1
effectively moves the ‘write one’ release and data-sample timing during standard mode communication out to 8s
and 22s, respectively. The recovery time is extended to 14s. This provides a less strict environment for long line
transmissions. Clearing this bit to logic 0 leaves the ‘write one’ release, data sampling, and recovery time (during
standard mode communication) at 5s, 15s, and 10s, respectively.
PPM (Bit 1): Presence Pulse Masking. This bit is used to enable/disable the presence pulse-masking function.
Setting this bit to logic 1 causes the bus master to initiate the beginning of a presence pulse during a 1-Wire reset.
This enables the master to prevent the larger amount of ringing caused by slave devices pulling the OW line low. If
the PPM bit is set, the PDR result bit in the interrupt flag register is always set, indicating that a slave device is
present on the OW line (even if there are none). Clearing the PPM bit to logic 0 disables the presence pulse-
masking function.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27468T17B55PA | CONN RCPT 55POS JAM NUT W/PINS |
| DS87C520-MNL+ | IC MCU EPROM/ROM 33MH IND 40-DIP |
| DS87C530-QCL+ | IC MCU EPR/ROM W/RTC 33MZ 52PLCC |
| DS80C320-MCL+ | IC MCU HI SPEED 33MHZ 40-DIP |
| MS27513E18B35S | CONN RCPT 66POS BOX MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS80C411-FNY+ | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS80CH11 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:System Energy Manager |
| DS80CH11+E02 | 制造商:Maxim from Components Direct 功能描述:MAXIM DS80CH11+E02 SYSTEM ENERGY MANAGERS - Trays 制造商:Maxim 功能描述:Maxim DS80CH11+E02 System Energy Managers |
| DS80CH11-E02 | 制造商:Maxim from Components Direct 功能描述:MAXIM DS80CH11-E02 SYSTEM ENERGY MANAGERS - Trays 制造商:Maxim 功能描述:Maxim DS80CH11-E02 System Energy Managers |
| DS80E100 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5 to 12.5 Gbps, Power-Saver Equalizer for Backplanes and Cables |
發布緊急采購，3分鐘左右您將得到回復。