- 您現在的位置：買賣IC網 > PDF目錄379183 > DS28E04S-100 4096-Bit Addressable 1-Wire EEPROM with PIO PDF資料下載
參數資料
| 型號： | DS28E04S-100 |
| 元件分類： | DRAM |
| 英文描述： | 4096-Bit Addressable 1-Wire EEPROM with PIO |
| 中文描述： | 4096位尋址1 - Wire EEPROM，帶有先鋒 |
| 文件頁數： | 12/36頁 |
| 文件大?。?/td> | 347K |
| 代理商： | DS28E04S-100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
DS28E04-100: 4096-Bit 1-Wire Addressable EEPROM with PIO
12 of 36
ADDRESS REGISTERS AND TRANSFER STATUS
The DS28E04-100 employs three address registers, called TA1, TA2, and E/S (Figure 8). Registers TA1 and TA2
must be loaded with the target address to which the data will be written or from which data is read. Register E/S is
a read-only transfer-status register, used to verify data integrity of write commands. The lower five bits of the E/S
register indicate the Ending Offset within the 32-byte scratchpad. Bit 5 of the E/S register, called PF, is set if the
number of data bits sent by the master is not an integer multiple of 8 or if the data in the scratchpad is not valid due
to a loss of power. A valid write to the scratchpad clears the PF bit. Bit 6 has no function; it always reads 0. Note
that the lowest five bits of the target address also determine the address within the scratchpad, where intermediate
storage of data will begin. This address is called byte offset. If the target address (TA1) for a Write command is
03CH for example, then the scratchpad stores incoming data beginning at the byte offset 1CH and is full after only
four bytes. The corresponding ending offset in this example is 1FH. For maximum data bandwidth, the target
address for writing should point to the beginning of a new page, i.e., the byte offset is 0. Thus the full 32-byte
capacity of the scratchpad is available, resulting also in the ending offset of 1FH. However, it is possible to write
one or several contiguous bytes somewhere within a page. The ending offset together with the partial flag support
the master checking the data integrity after a Write command. The highest valued bit of the E/S register, called AA
is valid only if the PF flag reads 0. If PF is 0 and AA is 1, a copy has taken place. Writing data to the scratchpad
clears the AA flag.
Figure 8. Address Registers
Bit #
7
6
5
4
3
2
1
0
Target Address (TA1)
T7
T6
T5
T4
T3
T2
T1
T0
Target Address (TA2)
T15
T14
T13
T12
T11
T10
T9
T8
Ending Address with
Data Status (E/S)
(Read Only)
AA
0
PF
E4
E3
E2
E1
E0
WRITING WITH VERIFICATION
To write data to the DS28E04-100 EEPROM sections, the scratchpad has to be used as intermediate storage. First
the master issues the Write Scratchpad command to specify the desired target address, followed by the data to be
written to the scratchpad. Under certain conditions (see Write Scratchpad command) the master will receive an
inverted CRC16 of the command, address (actual address sent), and data (as sent by the master) at the end of the
Write Scratchpad command sequence. Knowing this CRC value, the master can compare it to the value it has
calculated to decide whether the communication was successful and proceed to the Copy Scratchpad command. If
the master could not receive the CRC16, it should use the Read Scratchpad command to verify data integrity. As a
preamble to the scratchpad data, the DS28E04-100 repeats the target address TA1 and TA2 and sends the
contents of the E/S register. If the PF flag is set, data did not arrive correctly in the scratchpad or there was a loss
of power since data was last written to the scratchpad. The master does not need to continue reading; it can start a
new trial to write data to the scratchpad. Similarly, a set AA flag together with a cleared PF flag indicates that the
device did not recognize the Write command. If everything went correctly, both flags are cleared and the ending
offset indicates the address of the last byte written to the scratchpad. Now the master can continue reading and
verifying every data byte. After the master has verified the data, it can send the Copy Scratchpad command. This
command must be followed exactly by the data of the three address registers, TA1, TA2, and E/S. The master
should obtain the contents of these registers by reading the scratchpad.
相關PDF資料 |
PDF描述 |
|---|---|
| DS3151 | Single/Dual/Triple/Quad DS3/E3/STS-1 LIUs |
| DS3151N | Single/Dual/Triple/Quad DS3/E3/STS-1 LIUs |
| DS3152 | Single/Dual/Triple/Quad DS3/E3/STS-1 LIUs |
| DS3152N | Single/Dual/Triple/Quad DS3/E3/STS-1 LIUs |
| DS3153 | Single/Dual/Triple/Quad DS3/E3/STS-1 LIUs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS28E04S-100/T | 功能描述:電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| DS28E04S-100+ | 功能描述:電可擦除可編程只讀存儲器 4096-Bit Addressable 1-Wire 電可擦除可編程只讀存儲器 w/PIO RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| DS28E04S-100+T | 功能描述:電可擦除可編程只讀存儲器 4096-Bit Addressable 1-Wire 電可擦除可編程只讀存儲器 w/PIO RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| DS28E04S-224-BB+T | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
| DS28E05P+ | 功能描述:電可擦除可編程只讀存儲器 1W 1KB FTP MEMORY TSOC RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。