- 您現在的位置：買賣IC網 > PDF目錄379183 > DS2482-800 Eight-Channel 1-Wire Master PDF資料下載
參數資料
| 型號： | DS2482-800 |
| 英文描述： | Eight-Channel 1-Wire Master |
| 中文描述： | 八通道1-Wire主控制器 |
| 文件頁數： | 9/22頁 |
| 文件大小： | 261K |
| 代理商： | DS2482-800 |
DS2482-800: Eight-Channel 1-Wire Master
9 of 22
Logic Level (LL)
The LL bit reports the logic state of the active 1-Wire line without initiating any 1-Wire communication. The 1-Wire
line is sampled for this purpose every time the Status Register is read. The sampling and updating of the LL bit
takes place when the host processor has addressed the DS2482 in read mode (during the acknowledge cycle),
provided that the Read Pointer is positioned at the Status Register.
Device Reset (RST)
If the RST bit is 1, the DS2482 has performed an internal reset cycle, either caused by a power-on reset or from
executing the Device Reset command. The RST bit is cleared automatically when the DS2482 executes a Write
Configuration command to restore the selection of the desired 1-Wire features.
Single Bit Result (SBR)
The SBR bit reports the logic state of the active 1-Wire line sampled at t
MSR
of a 1-Wire Single Bit command or the
first bit of a 1-Wire Triplet command. The power-on default of SBR is 0. If the 1-Wire Single Bit command sends a
0-bit, SBR should be 0. With a 1-Wire Triplet command, SBR could be 0 as well as 1, depending on the response
of the 1-Wire devices connected. The same result applies to a 1-Wire Single Bit command that sends a 1-bit.
Triplet Second Bit (TSB)
The TSB bit reports the logic state of the active 1-Wire line sampled at t
MSR
of the second bit of a 1-Wire Triplet
command. The power-on default of TSB is 0. This bit is updated only with a 1-Wire Triplet command and has no
function with other commands.
Branch Direction Taken (DIR)
Whenever a 1-Write Triplet command is executed, this bit reports to the host processor the search direction that
was chosen by the 3rd bit of the triplet. The power-on default of DIR is 0. This bit is updated only with a 1-Wire
Triplet command and has no function with other commands. For additional information see the description of the 1-
Wire Triplet command and the Dallas Application Note 187, "1-Wire Search Algorithm".
FUNCTION COMMANDS
The DS2482 understands 9 function commands, which fall into four categories: device control, I2C communication,
1-Wire setup and 1-Wire communication. The feedback path to the host is controlled by a read pointer, which is set
automatically by each function command for the host to efficiently access relevant information. The host processor
sends these commands and applicable parameters as strings of one or two bytes using the I2C interface. The I2C
protocol requires that each byte be acknowledged by the receiving party to confirm acceptance or not be
acknowledged to indicate an error condition (invalid code or parameter) or to end the communication. Details of the
I2C protocol including acknowledge are found in the I2C interface description of this document.
Device Reset
Command Code
F0h
Command Parameter
None
Performs a global reset of device state machine logic, which in turn
selects IO0 as the active 1-Wire channel.
Terminates any ongoing 1-Wire communication.
Typical Use
Device initialization after power-up; re-initialization (reset) as desired.
Restriction
None (can be executed at any time)
Error Response
None
Maximum 525ns, counted from falling SCL edge of the command code
acknowledge bit.
Ends maximum 262.5ns after the falling SCL edge of the command code
acknowledge bit.
Read Pointer Position
Status Register (for busy polling)
RST set to 1,
1WB, PPD, SD, SBR, TSB, DIR set to 0
Configuration Bits Affected
1WS, APU, PPM, SPU set to 0
Description
Command Duration
1-Wire Activity
Status Bits Affected
相關PDF資料 |
PDF描述 |
|---|---|
| DS2482-100 | Single-Channel 1-Wire Master |
| DS2482S-100 | Single-Channel 1-Wire Master |
| DS2482S-800 | Eight-Channel 1-Wire Master |
| DS2502-E48 | 48-Bit Node Address Chip |
| DS26401 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2482-800_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:8-Channel 1-Wire Master |
| DS2482S-100 | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2482S-100/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Single-Channel 1-Wire Master |
| DS2482S-100/T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Single-Channel 1-Wire Master |
| DS2482S-100/T&R | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。