- 您現在的位置：買賣IC網 > PDF目錄379183 > DS2482-800 Eight-Channel 1-Wire Master PDF資料下載
參數資料
| 型號： | DS2482-800 |
| 英文描述： | Eight-Channel 1-Wire Master |
| 中文描述： | 八通道1-Wire主控制器 |
| 文件頁數： | 16/22頁 |
| 文件大?。?/td> | 261K |
| 代理商： | DS2482-800 |
DS2482-800: Eight-Channel 1-Wire Master
16 of 22
Figure 9. DS2482 Slave Address
A6
A5
A4
A3
A2
A1
A0
0
1
1
0
AD2
AD1
AD0
R/W
7-Bit Slave Address
Most Signi-
ficant Bit
Determines
Read or Write
AD2, AD1, AD0
Pin States
I2C Definitions
The following terminology is commonly used to describe I2C data transfers. The timing references are defined in
Figure 10.
Bus Idle or Not Busy:
Both, SDA and SCL, are inactive and in their logic HIGH states.
START Condition:
To initiate communication with a slave, the master has to generate a START condition. A
START condition is defined as a change in state of SDA from HIGH to LOW while SCL remains HIGH.
STOP Condition:
To end communication with a slave, the master has to generate a STOP condition. A STOP
condition is defined as a change in state of SDA from LOW to HIGH while SCL remains HIGH.
Repeated START Condition:
Repeated starts are commonly used for read accesses to select a specific data
source or address to read from. The master can use a repeated START condition at the end of a data transfer to
immediately initiate a new data transfer following the current one. A repeated START condition is generated the
same way as a normal START condition, but without leaving the bus idle after a STOP condition.
Data Valid:
With the exception of the START and STOP condition, transitions of SDA may occur only during the
LOW state of SCL. The data on SDA must remain valid and unchanged during the entire high pulse of SCL plus
the required setup and hold time (t
HD:DAT
after the falling edge of SCL and t
SU:DAT
before the rising edge of SCL, see
Figure 10). There is one clock pulse per bit of data. Data is shifted into the receiving device during the rising edge
of the SCL.
When finished with writing, the master must release the SDA line for a sufficient amount of setup time (minimum
t
SU:DAT
+ t
R
in Figure 10) before the next rising edge of SCL to start reading. The slave shifts out each data bit on
SDA at the falling edge of the previous SCL pulse and the data bit is valid at the rising edge of the current SCL
pulse. The master generates all SCL clock pulses, including those needed to read from a slave.
Acknowledge:
Usually, a receiving device, when addressed, is obliged to generate an acknowledge after the
receipt of each byte. The master must generate a clock pulse that is associated with this acknowledge bit. A device
that acknowledges must pull SDA LOW during the acknowledge clock pulse in such a way that SDA is stable LOW
during the HIGH period of the acknowledge-related clock pulse plus the required setup and hold time (t
HD:DAT
after
the falling edge of SCL and t
SU:DAT
before the rising edge of SCL).
Not Acknowledged by Slave:
A slave device may be unable to receive or transmit data, e.g., because it is busy
performing some real-time function. In this case the slave device will not acknowledge its slave address and leave
the SDA line HIGH.
A slave device that is ready to communicate will acknowledge at least its slave address. However, some time later
the slave may refuse to accept data, e.g., because of an invalid command code or parameter. In this case the slave
device will not acknowledge any of the bytes that it refuses and will leave SDA HIGH. In either case, after a slave
has failed to acknowledge, the master first needs to generate a repeated START condition or a STOP condition
followed by a START condition to begin a new data transfer.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2482-100 | Single-Channel 1-Wire Master |
| DS2482S-100 | Single-Channel 1-Wire Master |
| DS2482S-800 | Eight-Channel 1-Wire Master |
| DS2502-E48 | 48-Bit Node Address Chip |
| DS26401 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2482-800_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:8-Channel 1-Wire Master |
| DS2482S-100 | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2482S-100/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Single-Channel 1-Wire Master |
| DS2482S-100/T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Single-Channel 1-Wire Master |
| DS2482S-100/T&R | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。