參數資料
型號： DS2482-800
英文描述： Eight-Channel 1-Wire Master
中文描述： 八通道1-Wire主控制器
文件頁數： 15/22頁
文件大?。?/td> 261K
代理商： DS2482-800
DS2482-800: Eight-Channel 1-Wire Master
15 of 22
Bit Allocation in the Direction Byte
bit 7
bit 6
V
x
x = don’t care
I2C INTERFACE
General Characteristics
The I2C bus uses a data line (SDA) plus a clock signal (SCL) for communication. Both SDA and SCL are
bidirectional lines, connected to a positive supply voltage through a pullup resistor. When there is no
communication, both lines are HIGH. The output stages of devices connected to the bus must have an open-drain
or open-collector to perform the wired-AND function. Data on the I2C bus can be transferred at rates of up to
100kbps in the Standard-mode, up to 400kbps in the Fast-mode. The DS2482 works in both modes.
A device that sends data on the bus is defined as a transmitter, and a device receiving data as a receiver. The
device that controls the communication is called a “master.” The devices that are controlled by the master are
“slaves.” To be individually accessed, each device must have a slave address that does not conflict with other
devices on the bus.
Data transfers may be initiated only when the bus is not busy. The master generates the serial clock (SCL),
controls the bus access, generates the START and STOP conditions, and determines the number of data bytes
transferred between START and STOP (Figure 8). Data is transferred in bytes with the most significant bit being
transmitted first. After each byte follows an acknowledge bit to allow synchronization between master and slave.
Figure 8. I2C Protocol Overview
bit 5
x
bit 4
x
bit 3
x
bit 2
x
bit 1
x
bit 0
x
SCL
SDA
1
2
6
7
8
ACK
9
9
1
2
8
MS-bit
R/
W
Slave Address
ACK
bit
Acknowledgment
from Receiver
ACK
bit
START
Condition
ACK
Repeated if more bytes
are transferred
STOP Condition
Repeated START
Condition
Idle
Slave Address
The slave address to which the DS2482 responds is shown in Figure 9. The logic states at the address pins AD0,
AD1 and AD2 determine the value of the address bits A0, A1, and A2. The address pins allow the device to
respond to one of eight possible slave addresses.
The slave address is part of the slave-address/control byte. The
last bit of the slave-address/control byte (R/
W
) defines the data direction. When set to a 0, subsequent data will
flow from master to slave (write access); when set to a 1, data will flow from slave to master (read access).
相關PDF資料
PDF描述
DS2482-100 Single-Channel 1-Wire Master
DS2482S-100 Single-Channel 1-Wire Master
DS2482S-800 Eight-Channel 1-Wire Master
DS2502-E48 48-Bit Node Address Chip
DS26401 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
相關代理商/技術參數
參數描述
DS2482-800_12 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:8-Channel 1-Wire Master
DS2482S-100 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
DS2482S-100/R 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Single-Channel 1-Wire Master
DS2482S-100/T 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Single-Channel 1-Wire Master
DS2482S-100/T&R 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*