- 您現在的位置：買賣IC網 > PDF目錄379101 > CYV15G0404RB-BGXC (CYPRESS SEMICONDUCTOR CORP) Independent Clock Quad HOTLink II⑩ Deserializing Reclocker PDF資料下載
參數資料
| 型號： | CYV15G0404RB-BGXC |
| 廠商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | Independent Clock Quad HOTLink II⑩ Deserializing Reclocker |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PBGA256 |
| 封裝： | 27 X 27 MM, 1.57 MM HEIGHT, LEAD FREE, TBGA-256 |
| 文件頁數： | 9/27頁 |
| 文件大?。?/td> | 388K |
| 代理商： | CYV15G0404RB-BGXC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
CYV15G0404RB
Document #: 38-02102 Rev. *C
Page 9 of 27
LDTDEN
LVTTL Input,
internal pull up
Level Detect Transition Density Enable
. When LDTDEN is HIGH, the Signal
Level Detector, Range Controller, and Transition Density Detector are all enabled
to determine if the RXPLL tracks TRGCLKx± or the selected input serial data
stream. If the Signal Level Detector, Range Controller, or Transition Density
Detector are out of their respective limits while LDTDEN is HIGH, the RXPLL locks
to TRGCLKx± until they become valid. The SDASEL[A..D][1:0] inputs configure
the trip level of the Signal Level Detector. The Transition Density Detector limit is
one transition in every 60 consecutive bits. When LDTDEN is LOW, only the
Range Controller determines if the RXPLL tracks TRGCLKx± or the selected input
serial data stream. Set LDTDEN = HIGH.
Use Local Clock
. When ULCx is LOW, the RXPLL locks to TRGCLKx± instead
of the received serial data stream. While ULCx is LOW, the LFIx for the associated
channel is LOW, indicating a link fault.
When ULCx is HIGH, the RXPLL performs Clock and Data Recovery functions on
the input data streams. This function is used in applications that need a stable
RXCLKx±. When valid data transitions are absent for a long time, or the high-gain
differential serial inputs (INx±) are left floating, the RXCLKx± outputs may briefly
be different from TRGCLKx±.
Serial Rate Select
. The SPDSELx inputs specify the operating signaling-rate
range of each channel’s receive PLL.
LOW = 195–400 MBd
MID = 400–800 MBd
HIGH = 800–1500 MBd.
Receive Input Selector
. The INSELx input determines which external serial bit
stream passes to the receiver’s Clock and Data Recovery circuit. When INSELx
is HIGH, the Primary Differential Serial Data Input, INx1±, is the associated receive
channel. When INSELx is LOW, the Secondary Differential Serial Data Input,
INx2±, is the associated receive channel.
Link Fault Indication Output
. LFIx is an output status indicator signal. LFIx is the
logical OR of six internal conditions. LFIx asserts LOW when any of the following
conditions is true:
Received serial data rate is outside expected range
Analog amplitude is below expected levels
Transition density is lower than expected
Receive is channel disabled
ULCx is LOW
TRGCLKx± is absent.
ULCA
ULCB
ULCC
ULCD
LVTTL Input,
internal pull up
SPDSELA
SPDSELB
SPDSELC
SPDSELD
3-Level Select
[2]
static control input
INSELA
INSELB
INSELC
INSELD
LVTTL Input,
asynchronous
LFIA
LFIB
LFIC
LFID
LVTTL Output,
asynchronous
Device Configuration and Control Bus Signals
WREN
LVTTL input,
asynchronous,
internal pull up
ADDR[3:0]
LVTTL input
asynchronous,
internal pull up
Control Write Enable
. The WREN input writes the values of the DATA[7:0] bus
into the latch specified by the address location on the ADDR[3:0] bus.
[3]
Control Addressing Bus
. The ADDR[3:0] bus is the input address bus that
configures the device. The WREN input writes the values of the DATA[7:0] bus
into the latch specified by the address location on the ADDR[3:0] bus.
[3]
Table 3,
“Device Configuration and Control Latch Descriptions,” on page 14
lists the config-
uration latches within the device, and the initialization value of the latches when
RESET is asserted.
Table 4, “Device Control Latch Configuration Table,” on
page 16
shows how the latches are mapped in the device.
Notes
2. Use 3-Level Select inputs for static configuration. These are ternary inputs that use logic levels of LOW, MID, and HIGH. To implement the LOW level, connect
directly to V
(ground). To implement the HIGH level, connect directly to V
CC
(power). To implement the MID level, do not connect the input (leave floating),
which allows it to self bias to the proper level.
3. See
“Device Configuration and Control Interface” on page 13
for detailed information about the operation of the Configuration Interface.
Pin Definitions
(continued)
CYV15G0404RB Quad HOTLink II Deserializing Reclocker
Name
IO Characteristics
Signal Description
[+] Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| CYV15G0404RB | Independent Clock Quad HOTLink II Reclocking Deserializer(獨立時鐘，四路HOTLink II時鐘恢復串并轉換器) |
| CYV270M0101EQ | Adaptive Video Cable Equalizer (SOIC) |
| CYV270M0101EQ-SXC | Adaptive Video Cable Equalizer (SOIC) |
| CYW2338 | Dual Serial Input PLL with 2.5- and 1.1-GHz Prescalers |
| CYWM6935PAEC | WirelessUSB⑩ LR+PA Radio Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYV270101EQ-SXC | 制造商:Cypress Semiconductor 功能描述: |
| CYV270M0101EQ | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Adaptive Video Cable Equalizer |
| CYV270M0101EQ_0710 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Adaptive Video Cable Equalizer |
| CYV270M0101EQ-SXC | 功能描述:多媒體雜項 Std Definition Video Equalizr COM RoHS:否 制造商:Texas Instruments 類型: 通道數量: 轉換速率:540 Mbps 分辨率: 封裝 / 箱體:SOIC-16 封裝:Tube |
| CYV270M0101EQ-SXCES | 制造商:Cypress Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。