- 您現在的位置：買賣IC網 > PDF目錄378513 > CY7C9689-AI (CYPRESS SEMICONDUCTOR CORP) TAXI Compatible HOTLink Transceiver PDF資料下載
參數資料
| 型號： | CY7C9689-AI |
| 廠商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | TAXI Compatible HOTLink Transceiver |
| 中文描述： | 1 CHANNEL(S), 200M bps, LOCAL AREA NETWORK CONTROLLER, PQFP100 |
| 封裝： | PLASTIC, TQFP-100 |
| 文件頁數： | 11/48頁 |
| 文件大?。?/td> | 1009K |
| 代理商： | CY7C9689-AI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
CY7C9689
11
28
FIFOBYP
Static control input
TTL levels
Normally wired HIGH
or LOW
FIFO Bypass Enable.
When asserted, the Transmit and Receive FIFOs are bypassed. In this mode
TXCLK is not used. Instead all transmit data must be synchronous to REFCLK.
Transmit FIFO status flags are synchronized to REFCLK. All received data is
synchronous to RXCLK output. Receive FIFO status flags are synchronized to
RXCLK (the recovered Receive PLL character clock).
When not asserted, the Transmit and Receive FIFOs are enabled. In this mode
all Transmit FIFO writes are synchronized to TXCLK, and all Receive FIFO
reads are synchronous to the RXCLK input.
8/10-bit Parallel Data Size Select.
When set for 8-bit data (BYTE8/10 is HIGH) and the encoder is enabled
(ENCBYP is HIGH), 8-bit DATA characters and 4-bit COMMAND characters are
captured at the TXDATA[7:0] or TXCMD[3:0] inputs (selected by the TXSC/D
input) and passed to the Transmit FIFO (if enabled) and encoder. Received
characters are decoded, passed through the Receive FIFO (if enabled) and
presented at either the RXDATA[7:0] or RXCMD[3:0] outputs and indicated by
the RXSC/D output.
When set for 8-bit data (BYTE8/10 is HIGH) and the encoder is bypassed
(ENCBYP is LOW), the internal data paths are set for 10-bit characters. Each
received character is presented to the Receive FIFO (if enabled) and is passed
to the RXDATA[9:0] outputs.
When set for 10-bit data (BYTE8/10 is LOW) and the encoder is enabled
(ENCBYP is HIGH), 10-bit DATA characters and 2-bit COMMAND characters
are captured at the TXDATA[9:0] or TXCMD[1:0] inputs (selected by the TXSC/D
input) and passed to the Transmit FIFO (if enabled) and encoder. Received
characters are decoded, passed through the Receive FIFO (if enabled) and
presented at either the RXDATA[9:0] or RXCMD[1:0] outputs and indicated by
the RXSC/D output.
When set for 10-bit data (BYTE8/10 is LOW) and the encoder is bypassed
(ENCBYP is LOW), the internal clock data paths are set for 12-bit characters.
Each received character is presented to the Receive FIFO (if enabled) and is
passed to the RXDATA[9:0] and the RXCMD[1:0] outputs.
External FIFO Mode.
EXTFIFO modifies the active state of the RXEN and TXEN inputs and the timing
of the Transmitter and Receiver data buses. When configured for external FIFOs
(EXTFIFO is HIGH), TXEN is assumed to be driven by the empty flag of an
attached CY7C42X5 FIFO, and RXEN is assumed to be driven by the almost
full flag of an attached CY7C42X5 FIFO. In this mode the active data transition
is in the clock following the clock edge that
“
enables
”
the data bus.
When not configured for external FIFOs (EXTFIFO is LOW), TXEN is assumed
to be driven as a pipeline register and RXEN is assumed to be driven by a
controller for a pipeline register. In this mode the active data transition is within
the same clock as the clock edge that
“
enables
”
the data bus.
EXTFIFO also modifies the output state of the Receive and Transmit FIFO flags.
When configured for external FIFOs (EXTFIFO is HIGH), the Full and Empty
FIFO flags are active HIGH (the Half full flag is always active LOW). When not
configured for external FIFOs (EXTFIFO is LOW), all of the FIFO flags are active
LOW.
Enable Encoder Bypass Mode.
When asserted, both the encoder and decoder are bypassed. Data is transmit-
ted without 4B/5B or 5B/6B encoding (but with NRZI encoding), LSB first. Re-
ceived data are presented as parallel characters to the parallel interface without
decoding.
When deasserted, data is passed through both the encoder in the Transmit path
and the decoder in the Receive path.
50
BYTE8/10
Static control input
TTL levels
Normally wired HIGH
or LOW
49
EXTFIFO
Static control input
TTL levels
Normally wired HIGH
or LOW
27
ENCBYP
Static control input
TTL levels
Normally wired HIGH
or LOW
Pin Descriptions
(continued)
Pin
Name
I/O Characteristics
Signal Description
相關PDF資料 |
PDF描述 |
|---|---|
| CY8C21323 | PSoC Mixed-Signal Array(PSoC混合信號陣列) |
| CY8C21123 | PSoC Mixed-Signal Array(PSoC混合信號陣列) |
| CY8C21223 | PSoC Mixed-Signal Array(PSoC混合信號陣列) |
| CY8C21634-24AX | PSoC Mixed-Signal Array |
| CY8C21534 | PSoC Mixed-Signal Array |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY7C9915JXC-5 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CY7C9915JXI-1 | 功能描述:IC CLK BUFF SKEW 8OUT 32PLCC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:RoboClock™ 產品變化通告:Product Discontinuation 04/May/2011 標準包裝:96 系列:- 類型:時鐘倍頻器，零延遲緩沖器 PLL:帶旁路 輸入:LVTTL 輸出:LVTTL 電路數:1 比率 - 輸入:輸出:1:8 差分 - 輸入:輸出:無/無 頻率 - 最大:133.3MHz 除法器/乘法器:是/無 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:管件 其它名稱:23S08-5HPGG |
| CY7C9915JXI-1T | 功能描述:IC CLK BUFF SKEW 8OUT 32PLCC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:RoboClock™ 產品變化通告:Product Discontinuation 04/May/2011 標準包裝:96 系列:- 類型:時鐘倍頻器，零延遲緩沖器 PLL:帶旁路 輸入:LVTTL 輸出:LVTTL 電路數:1 比率 - 輸入:輸出:1:8 差分 - 輸入:輸出:無/無 頻率 - 最大:133.3MHz 除法器/乘法器:是/無 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:管件 其它名稱:23S08-5HPGG |
| CY7C9915JXI-5 | 制造商:Cypress Semiconductor 功能描述: |
| CY7CD68321C-56LFXC | 制造商:Rochester Electronics LLC 功能描述: 制造商:Cypress Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。