參數資料
型號： CY7C63743C
廠商： Cypress Semiconductor Corp.
英文描述： enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器)
中文描述： 的enCoRe USB的組合低速USB和PS / 2外設控制器（的enCoRe的USB結合低速的USB和的PS / 2外設控制器）
文件頁數： 17/49頁
文件大小： 1942K
代理商： CY7C63743C
CY7C63722C
CY7C63723C
CY7C63743C
FOR
FOR
Document #: 38-08022 Rev. *C
Page 17 of 49
13.2
USB status and control is regulated by the USB Status and
Control Register as shown in
Figure 13-1
.
USB Port Status and Control
Bit 7: PS/2 Pull-up Enable
This bit is used to enable the internal PS/2 pull-up resistors
on the SDATA and SCLK pins. Normally the output high
level on these pins is V
CC
, but note that the output will be
clamped to approximately 1 Volt above V
REG
if the VREG
Enable bit is set, or if the Device Address is enabled (bit 7
of the USB Device Address Register,
Figure 14-1
).
1 = Enable PS/2 Pull-up resistors. The SDATA and SCLK
pins are pulled up internally to V
CC
with two resistors of
approximately 5 k
(see Section 25.0 for the value of
R
PS2
).
0 = Disable PS/2 Pull-up resistors.
Bit 6: V
REG
Enable
A 3.3V voltage regulator is integrated on chip to provide a
voltage source for a 1.5-k
pull-up resistor connected to
the D– pin as required by the USB Specification. Note that
the VREG output has an internal series resistance of ap-
proximately 200
, the external pull-up resistor required is
approximately 1.3-k
(see
Figure 16-1
).
1 = Enable the 3.3V output voltage on the VREG pin.
0 = Disable. The VREG pin can be configured as an input.
Bit 5: USB-PS/2 Interrupt Select
This bit allows the user to select whether an USB bus reset
interrupt or a PS/2 activity interrupt will be generated when
the interrupt conditions are detected.
1 = PS/2 interrupt mode. A PS/2 activity interrupt will occur
if the SDATA pin is continuously LOW for 128 to 256
μ
s.
0 = USB interrupt mode (default state). In this mode, a USB
bus reset interrupt will occur if the single ended zero (SE0,
D– and D+ are LOW) exists for 128 to 256
μ
s.
See Section 21.3 for more details.
Bit 4:
Reserved. Must be written as a ‘0’.
Bit 3: USB Bus Activity
The Bus Activity bit is a “sticky” bit that detects any non-idle
USB event has occurred on the USB bus. Once set to HIGH
by the SIE to indicate the bus activity, this bit retains its
logical HIGH value until firmware clears it. Writing a ‘0’ to
this bit clears it; writing a ‘1’ preserves its value. The user
firmware should check and clear this bit periodically to de-
tect any loss of bus activity. Firmware can clear the Bus
Activity bit, but only the SIE can set it. The 1.024-ms timer
interrupt service routine is normally used to check and clear
the Bus Activity bit.
1 = There has been bus activity since the last time this bit
was cleared. This bit is set by the SIE.
0 = No bus activity since last time this bit was cleared (by
firmware).
Bit [2:0]: D+/D– Forcing Bit [2:0]
Forcing bits allow firmware to directly drive the D+ and D–
pins, as shown in
Table 13-1
. Outputs are driven with con-
trolled edge rates in these modes for low EMI. For forcing
the D+ and D– pins in USB mode, D+/D– Forcing Bit 2
should be 0. Setting D+/D– Forcing Bit 2 to ‘1’ puts both
pins in an open-drain mode, preferred for applications such
as PS/2 or LED driving.
Note:
2.
For PS/2 operation, the D+/D– Forcing Bit [2:0] = 111b mode must be set initially (one time only) before using the other PS/2 force modes.
Bit #
7
6
5
4
3
2:0
Bit
Name
PS/2
Pull-up
Enable
VREG
Enable
USB
Reset-
PS/2
Activity
Interrupt
Mode
Reserved
USB
Bus
Activity
D+/D–
Forcing
Bit
Read/
Write
R/W
R/W
R/W
-
R/W
R/W
Reset
0
0
0
0
0
0
0
0
Figure 13-1. USB Status and Control Register (Address
0x1F)
Table 13-1. Control Modes to Force D+/D– Outputs
D+/D– Forcing
Bit [2:0]
Control Action
Application
000
Not forcing (SIE controls driver)
Any Mode
001
Force K (D+ HIGH, D– LOW)
USB Mode
010
Force J (D+ LOW, D– HIGH)
011
Force SE0 (D– LOW, D+ LOW)
100
Force D– LOW, D+ LOW
PS/2 Mode
[2]
101
Force D– LOW, D+ HiZ
110
Force D– HiZ, D+ LOW
111
Force D– HiZ, D+ HiZ
相關PDF資料
PDF描述
CY7C63723C enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器)
CY7C63803 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63310 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63801 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63823 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
相關代理商/技術參數
參數描述
CY7C63743C-PXC 功能描述:輸入/輸出控制器接口集成電路 USB Combo Lo Spd PS/2 Periphrl Cntrlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743C-QXC 功能描述:輸入/輸出控制器接口集成電路 LO Speed 3 Endpoint USB COM RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743C-SXC 功能描述:輸入/輸出控制器接口集成電路 USB Combo Lo Spd PS/2 Periphrl Cntrlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743C-SXCT 功能描述:輸入/輸出控制器接口集成電路 USB/PS/2 Combo LoSpd Peripheral Controlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743-PC 功能描述:IC MCU 8K LS USB/PS-2 24-DIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*