參數資料
型號： CY7C63743C
廠商： Cypress Semiconductor Corp.
英文描述： enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器)
中文描述： 的enCoRe USB的組合低速USB和PS / 2外設控制器（的enCoRe的USB結合低速的USB和的PS / 2外設控制器）
文件頁數： 16/49頁
文件大小： 1942K
代理商： CY7C63743C
CY7C63722C
CY7C63723C
CY7C63743C
FOR
FOR
Document #: 38-08022 Rev. *C
Page 16 of 49
12.1
Port 2 serves as an auxiliary input port as shown in
Figure 12-8
. The Port 2 inputs all have TTL input thresholds.
Auxiliary Input Port
Bit [7:6]:
Reserved
Bit [5:4]: D+ (SCLK) and D– (SDATA) States
The state of the D+ and D– pins can be read at Port 2 Data
Register. Performing a read from the port pins returns their
logic values.
1 = Port Pin is logic HIGH
0 = Port Pin is logic LOW
Bit [3:2]:
Reserved
Bit 1: P2.1 (Internal Clock Mode Only)
In the Internal Clock mode, the XTALIN pin can serve as a
general purpose input, and its state can be read at Port 2,
Bit 1 (P2.1). See Section 9.1 for more details.
1 = Port Pin is logic HIGH
0 = Port Pin is logic LOW
Bit 0: P2.0/VREG Pin State
In PS/2 mode, the VREG
pin can be used as an input and
its state can be read at port P2.0. Section 15.0 for more
details.
1 = Port Pin is logic HIGH
0 = Port Pin is logic LOW
13.0
USB Serial Interface Engine (SIE)
The SIE allows the microcontroller to communicate with the
USB host. The SIE simplifies the interface between the micro-
controller and USB by incorporating hardware that handles the
following USB bus activity independently of the microcon-
troller:
Translate the encoded received data and format the data to
be transmitted on the bus.
CRC checking and generation. Flag the microcontroller if
errors exist during transmission.
Address checking. Ignore the transactions not addressed
to the device.
Send appropriate ACK/NAK/STALL handshakes.
Token type identification (SETUP, IN, or OUT). Set the ap-
propriate token bit once a valid token is received.
Place valid received data in the appropriate endpoint FIFOs.
Send and update the data toggle bit (Data1/0).
Bit stuffing/unstuffing.
Firmware is required to handle the rest of the USB interface
with the following tasks:
Coordinate enumeration by decoding USB device requests.
Fill and empty the FIFOs.
Suspend/Resume coordination.
Verify and select Data toggle values.
13.1
A typical USB enumeration sequence is shown below. In this
description, ‘Firmware’ refers to embedded firmware in the
CY7C637xxC controller.
1. The host computer sends a SETUP packet followed by a
DATA packet to USB address 0 requesting the Device de-
scriptor.
2. Firmware decodes the request and retrieves its Device
descriptor from the program memory tables.
3. The host computer performs a control read sequence and
Firmware responds by sending the Device descriptor over
the USB bus, via the on-chip FIFO.
4. After receiving the descriptor, the host sends a SETUP
packet followed by a DATA packet to address 0 assigning
a new USB address to the device.
5. Firmware stores the new address in its USB Device
Address Register after the no-data control sequence
completes.
6. The host sends a request for the Device descriptor using
the new USB address.
7. Firmware decodes the request and retrieves the Device
descriptor from program memory tables.
8. The host performs a control read sequence and Firmware
responds by sending its Device descriptor over the USB
bus.
9. The host generates control reads from the device to request
the Configuration and Report descriptors.
10.Once the device receives a Set Configuration request, its
functions may now be used.
11.Firmware should take appropriate action for Endpoint 1
and/or 2 transactions, which may occur from this point.
USB Enumeration
Table 12-1. Ports 0 and 1 Output Control Truth Table
Data
Register
Mode1 Mode0 Output Drive
Strength
Input
Threshold
0
0
0
Hi-Z
CMOS
1
Hi-Z
TTL
0
0
1
Medium
(8 mA) Sink
CMOS
1
High Drive
CMOS
0
1
0
Low (2 mA)
Sink
CMOS
1
Resistive
CMOS
0
1
1
High (50 mA)
Sink
CMOS
1
High Drive
CMOS
Bit #
7
6
5
4
3
2
1
0
Bit
Name
Reserved
D+
(SCLK)
State
D–
(SDATA)
State
Reserved
P2.1
(Internal
Clock
Mode
Only)
P2.0
VREG
Pin
State
Read/
Write
-
-
R
R
-
-
R
R
Reset
0
0
0
0
0
0
0
0
Figure 12-8. Port 2 Data Register (Address 0x02)
相關PDF資料
PDF描述
CY7C63723C enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器)
CY7C63803 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63310 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63801 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63823 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
相關代理商/技術參數
參數描述
CY7C63743C-PXC 功能描述:輸入/輸出控制器接口集成電路 USB Combo Lo Spd PS/2 Periphrl Cntrlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743C-QXC 功能描述:輸入/輸出控制器接口集成電路 LO Speed 3 Endpoint USB COM RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743C-SXC 功能描述:輸入/輸出控制器接口集成電路 USB Combo Lo Spd PS/2 Periphrl Cntrlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743C-SXCT 功能描述:輸入/輸出控制器接口集成電路 USB/PS/2 Combo LoSpd Peripheral Controlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743-PC 功能描述:IC MCU 8K LS USB/PS-2 24-DIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*