參數資料
型號： CY7C43644
廠商： Cypress Semiconductor Corp.
英文描述： 1K x36 x2 Bidirectional Synchronous FIFO w/ Bus Matching(1K x36 x2 雙向同步先進先出帶總線匹配)
中文描述： 每1000 x36 x2雙向同步FIFO瓦特/總線匹配（每1000 x36 x2雙向同步先進先出帶總線匹配）
文件頁數： 28/37頁
文件大小： 581K
代理商： CY7C43644
CY7C43624
CY7C43634/CY7C43644
CY7C43664/CY7C43684
28
PRELIMINARY
Signal Description
Master Reset (MRS1, MRS2)
Each of the two FIFO memories of the CY7C436X4 undergoes
a complete reset by taking its associated Master Reset
(MRS1, MRS2) input LOW for at least four Port A clock (CLKA)
and four Port B clock (CLKB) LOW-to-HIGH transitions. The
Master Reset inputs can switch asynchronously to the clocks.
A Master Reset initializes the internal read and write pointers
and forces the Full/Input Ready flag (FFA/IRA, FFB/IRB) LOW,
the Empty/Output Ready flag (EFA/ORA, EFB/ORB) LOW, the
Almost Empty flag (AEA, AEB) LOW, and the Almost Full flag
(AFA, AFB) HIGH. A Master Reset also forces the Mailbox flag
(MBF1, MBF2) of the parallel mailbox register HIGH. After a
Master Reset, the FIFO
’
s Full/Input Ready flag is set HIGH
after two clock cycles to begin normal operation. A Master Re-
set must be performed on the FIFO after power up, before data
is written to its memory.
A LOW-to-HIGH transition on a FIFO Master Reset (MRS1,
MRS2) input latches the value of the Big Endian (BE) input or
determining the order by which bytes are transferred through
Port B.
A LOW-to-HIGH transition on a FIFO reset (MRS1, MRS2)
input latches the values of the Flag select (FS0, FS1) and Se-
rial Programming Mode (SPM) inputs for choosing the Almost
Full and Almost Empty offset programming method (see Al-
most Empty and Almost Full flag offset programming below).
Partial Reset (PRS1, PRS2)
Each of the two FIFO memories of the CY7C436X4 undergoes
a limited reset by taking its associated Partial Reset (PRS1,
PRS2) input LOW for at least four Port A clock (CLKA) and four
Port B clock (CLKB) LOW-to-HIGH transitions. The Partial Re-
set inputs can switch asynchronously to the clocks. A Partial
Reset initializes the internal read and write pointers and forces
the Full/Input Ready flag (FFA/IRA, FFB/IRB) LOW, the Empty/
Output Ready flag (EFA/ORA, EFB/ORB) LOW, the Almost
Empty flag (AEA, AEB) LOW, and the Almost Full flag (AFA,
AFB) HIGH. A Partial Reset also forces the Mailbox flag
(MBF1, MBF2) of the parallel mailbox register HIGH. After a
Partial Reset, the FIFO
’
s Full/Input Ready flag is set HIGH
after two clock cycles to begin normal operation.
Whatever flag offsets, programming method (parallel or seri-
al), and timing mode (FWFT or CY Standard mode) are cur-
rently selected at the time a Partial Reset is initiated, those
settings will remain unchanged upon completion of the reset
operation. A Partial Reset may be useful in the case where
reprogramming a FIFO following a Master Reset would be in-
convenient.
Big Endian/First-Word Fall-Through (BE/FWFT)
This is a dual-purpose pin. At the time of Master Reset, the BE
select function is active, permitting a choice of big or little en-
dian byte arrangement for data written to or read from Port B.
This selection determines the order by which bytes (or words)
of data are transferred through this port. For the following illus-
trations, assume that a byte (or word) bus size has been se-
lected for Port B. (Note that when Port B is configured for a
long-word size, the Big Endian function has no application and
the BE input is a
“
don
’
t care
”
.)
A HIGH on the BE/FWFT input when the Master Reset (MRS1
and MRS2) inputs go from LOW to HIGH will select a Big En-
dian arrangement. When data is moving in the direction from
Port A to Port B, the most significant byte (word) of the long
word written to Port A will be read from Port B first; the least
significant byte (word) of the long-word written to Port A will be
read from Port B last. When data is moving in the direction
from Port B to Port A, the byte (word) written to Port B first will
be read from Port A as the most significant byte (word) of the
long-word; the byte (word) written to Port B last will be read
from Port A as the least significant byte (word) of the long
word.
A LOW on the BE/FWFT input when the Master Reset (MRS1
and MRS2) inputs go from LOW to HIGH will select a Little
Endian arrangement. When data is moving in the direction
from Port A to Port B, the least significant byte (word) of the
long-word written to Port A will be read from Port B first; the
most significant byte (word) of the long-word written to Port A
will be read from Port B last. When data is moving in the direc-
tion from Port B to Port A, the byte (word) written to Port B first
will be read from Port A as the least significant byte (word) of
the long-word; the byte (word) written to Port B last will be read
from Port A as the most significant byte (word) of the long-
word.
After Master Reset, the FWFT select function is active, permit-
ting a choice between two possible timing modes: CY Stan-
dard mode or First-Word Fall-Through (FWFT) mode. Once
the Master Reset (MRS1, MRS2) input is HIGH, a HIGH on the
BE/FWFT input at the second LOW-to-HIGH transition of
CLKA (for FIFO1) and CLKB (for FIFO2) will select CY Stan-
dard mode. This mode uses the Empty Flag function (EFA,
EFB) to indicate whether or not there are any words present in
the FIFO memory. It uses the Full Flag function (FFA, FFB) to
indicate whether or not the FIFO memory has any free space
for writing. In CY Standard mode, every word read from the
FIFO, including the first, must be requested using a formal
read operation.
Once the Master Reset (MRS1,MRS2) input is HIGH, a LOW
on the BE/FWFT input during the next LOW-to-HIGH transition
of CLKA (for FIFO1) and CLKB (for FIFO2) will select FWFT
mode. This mode uses the Output Ready function (ORA,
ORB) to indicate whether or not there is valid data at the data
outputs (A
0
–
35
or B
0
–
35
). It also uses the Input Ready function
(IRA, IRB) to indicate whether or not the FIFO memory has any
free space for writing. In the FWFT mode, the first word written
to an empty FIFO goes directly to data outputs, no read re-
quest necessary. Subsequent words must be accessed by
performing a formal read operation.
Following Master Reset, the level applied to the BE/FWFT in-
put to choose the desired timing mode must remain static
throughout the FIFO operation.
Programming the Almost Empty and Almost Full Flags
Four registers in the CY7C436X4 are used to hold the offset
values for the Almost Empty and Almost Full flags. The Port B
Almost Empty flag (AEB) offset register is labeled X1 and the
Port A Almost Empty flag (AEA) offset register is labeled X2.
The Port A Almost Full flag (AFA) offset register is labeled Y1
and the Port B Almost Full flag (AFB) offset register is labeled
Y2. The index of each register name corresponds with preset
values during the reset of a FIFO, programmed in parallel us-
ing the FIFO
’
s Port A data inputs, or programmed in serial
using the Serial Data (SD) input (see
Table 1
).
To load a FIFO
’
s Almost Empty flag and Almost Full flag offset
registers with one of the three preset values listed in
Table 1
,
the Serial Program Mode (SPM) and at least one of the flag-
相關PDF資料
PDF描述
CY7C43664 4K x36 x2 Bidirectional Synchronous FIFO w/ Bus Matching(4K x36 x2 雙向同步先進先出帶總線匹配)
CY7C43684 16K x36 x2 Bidirectional Synchronous FIFO w/ Bus Matching(16K x36 x2 雙向同步先進先出帶總線匹配)
CY7C43636 512 x36/x18x2 Tri Bus FIFO(512 x36/x18x2 三路總線 先進先出)
CY7C43626 256 x36/x18x2 Tri Bus FIFO(256 x36/x18x2 三路總線先進先出)
CY7C43646 1K x36/x18x2 Tri Bus FIFO(1K x36/x18x2 三路總線 先進先出)
相關代理商/技術參數
參數描述
CY7C43644AV-10AC 制造商:Cypress Semiconductor 功能描述:FIFO Mem Sync Dual Depth/Width Bi-Dir 1K x 36 x 2 128-Pin TQFP
CY7C43663-15AC 制造商:Rochester Electronics LLC 功能描述:- Bulk
CY7C43664-7AC 制造商:Rochester Electronics LLC 功能描述:- Bulk
CY7C43682-15AC 制造商:Rochester Electronics LLC 功能描述:- Bulk
CY7C43683-10AI 制造商:Rochester Electronics LLC 功能描述:- Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*