- 您現在的位置：買賣IC網 > PDF目錄369673 > CSP1027 CSP1027 Voice Band Codec for Cellular Handset and Modem Applications PDF資料下載
參數資料
| 型號： | CSP1027 |
| 元件分類： | Codec |
| 英文描述： | CSP1027 Voice Band Codec for Cellular Handset and Modem Applications |
| 中文描述： | CSP1027語音頻帶編解碼器的蜂窩手機和調制解調器應用 |
| 文件頁數： | 24/64頁 |
| 文件大?。?/td> | 937K |
| 代理商： | CSP1027 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
CSP1027 Voice Band Codec for
Cellular Handset and Modem Applications
Data Sheet
December 1999
Lucent Technologies Inc.
24
4 Architectural Information
(continued)
During each time slot (see Figure 26 on page 25), the
device that is assigned to that time slot drives the ADD
and DATA lines. If the assigned device's output buffer is
full, it loads its output shift register and shifts the 16 bits
of data, MSB first, out DO onto the DATA line. The 8-bit
transmit address is inverted and shifted out, LSB first,
onto the ADD line at the same time as the first 8 bits of
data. The inverted 8-bit protocol information is then
shifted out, LSB first, on the ADD line at the same time
as the last 8 bits of data. The CSP1027’s transmit
address, AT[7:0], is determined by the SMODE0 pin
(see Table 6 on page 25). The DSP’s transmit address
is determined by the
srta
register. The CSP1027’s pro-
tocol information is always all zeros, which is inverted
to appear as all ones on the ADD line. The DSP’s pro-
tocol information is determined by the
saddx
register. If
during a time slot the assigned device's output buffer is
empty, then zeros are shifted out on the DATA line and
zeros are shifted and inverted to become ones on the
ADD line.
During each time slot, each device receives the data on
the DATA line and inverts and receives the address and
protocol information on the ADD line. Each device
compares the transmitted 8-bit address with its receive
address. If the transmitted address and the device's
receive address have at least one occurrence of a one
in the same bit location, the address matches and the
device transfers the data from the input shift register to
its input buffer. If the transmitted address and the
receive address do not match, the data remains in the
input shift register and is overwritten during the next
time slot. The DSP's receive address is determined by
its
srta
register. Each CSP1027 has two receive
addresses, one for data and another for control, the
values of these two addresses are determined by the
SMODE0 pin (see Table 7 on page 26). When the data
receive address matches, the input shift register is
loaded into the
cdx(D/A)
register. When the control
receive address matches, the input shift register is
loaded into one of the four
cioc
registers, based upon
the two most significant bits of the 16-bit word. The
CSP1027 ignores the protocol information.
Multiprocessor communication with a CSP1027 is
intended to follow the sequence:
I
The DSP writes the control registers,
cioc
[0:3], in the
CSP1027 to configure the clock dividers and codec.
The codec is also activated.
I
The CSP1027’s A/D fills the output buffer,
cdx(A/D)
,
and empties the input buffer,
cdx(D/A)
, at the same
time. This causes the A/D data to be transmitted by
the CSP1027 to the DSP during the next CSP1027
time slot. The DSP’s receive address is set to match
the CSP1027’s transmit address.
I
When the DSP receives A/D data from the CSP1027,
it responds by sending D/A data to the CSP1027 dur-
ing the DSP’s next time slot. The DSP’s transmit
address is set to match the CSP1027’s data receive
address. The new data is loaded into the CSP1027’s
cdx(D/A)
register to be used as the next D/A sample.
I
If the DSP wants to send a control word to the
CSP1027 to change the configuration or inactivate
the codec, this can be done by setting the DSP's
transmit address to match the codec's control
receive address.
Note that since the CSP1027 sends all zeros for the
protocol information, this will have to be used to identify
the A/D data from the CSP1027. If two CSP1027s are
connected to the multiprocessor bus and the DSP's
receive address is set to match both CSP1027's trans-
mit addresses, the DSP will have to identify which A/D
data came from which CSP1027 by the order in which
the data arrives, since both CSP1027s will be sending
the same protocol information.
相關PDF資料 |
PDF描述 |
|---|---|
| CT1469-2 | CT1469-2 MIL-STD-1397 Type E 10MHz Transceiver |
| CT1496-2 | CT1496-2 MIL-STD-1397 Type E 10MHz Low Level Serial Manchester 32 Bit Encoder |
| CT1508-2 | CT1508-2 MIL-STD-1397 Type E 10MHz Serial Manchester 4-Bit SIS / SOS Decoder |
| CT1611 | DMA Controller with Buffer Memory,MIL-STD-1750A Compatible |
| CT1611-FP | DMA Controller with Buffer Memory,MIL-STD-1750A Compatible |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CSP1027J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC |
| CSP1027-J11-DB | 制造商:Alcatel-Lucent 功能描述: |
| CSP1027S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC |
| CSP1027-S11-DB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CSP1034AH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
發布緊急采購，3分鐘左右您將得到回復。