- 您現在的位置：買賣IC網 > PDF目錄369673 > CSP1027 CSP1027 Voice Band Codec for Cellular Handset and Modem Applications PDF資料下載
參數資料
| 型號： | CSP1027 |
| 元件分類： | Codec |
| 英文描述： | CSP1027 Voice Band Codec for Cellular Handset and Modem Applications |
| 中文描述： | CSP1027語音頻帶編解碼器的蜂窩手機和調制解調器應用 |
| 文件頁數： | 13/64頁 |
| 文件大小： | 937K |
| 代理商： | CSP1027 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
Lucent Technologies Inc.
13
Data Sheet
December 1999
CSP1027 Voice Band Codec for
Cellular Handset and Modem Applications
4 Architectural Information
(continued)
4.2.7 Digital-to-Analog Path
Starting at the bottom right of Figure 3 on page 5, the
-
Σ
D/A conversion process begins with a 16-bit two's
complement PCM signal read from the DI serial input.
The PCM is interpolated up to 1 MHz in two stages and
low-pass filtered at each stage to attenuate 8 kHz
images.
The PCM input is latched into the
cdx(D/A)
register at
a nominal word rate of 8 kHz. The signal is then option-
ally high-pass filtered. This filter has the same transfer
function as the A/D high-pass filter.
A digital sample-and-hold increases the word rate by a
factor of 5 from 8 kHz to 40 kHz. The seventh-order IIR
digital low-pass filter then removes the spectral images
between 4 kHz and 20 kHz and predistorts the pass-
band to compensate for the filtering done during the
interpolation up to the 1 MHz word rate. The transfer
function of this low-pass filter is the same as the one
employed in the A/D converter.
The output of the low-pass filter feeds a programmable
gain adjustment block that serves as a volume control.
The gain can be changed in 3 dB increments from
0 dB to –45 dB. The attenuation level is set by writing
the OGSEL field in the
cioc0
register (see Table 7 on
page 26).
The digital modulator block further increases the word
rate by a factor of 25 from 40 kHz to 1 MHz. Through
quantization and noise shaping, the digital
-
Σ
modula-
tor creates 1-bit output words at 1 MHz.
The modulator 1-bit output drives a structure combining
a 1-bit D/A converter and a second-order switched-
capacitor filter having a cutoff frequency of 8 kHz
(based on a 1 MHz clock). This is all shown as the D/A
block in Figure 3 on page 5.
This is followed by a second-order active Chebychev fil-
ter having a cutoff frequency of 35 kHz.
The passband ripple of the analog filters is small
enough such that they have virtually no effect on the
passband response.
The output amplifier buffers the analog filter output.
The frequency responses of the A/D and D/A paths are
essentially the same. See Figures 6 through 15 for the
magnitude and delay responses versus frequency.
4.3 Programmable Features
4.3.1 Active/Inactive Modes
The CSP1027 has active and inactive modes of opera-
tion which are selected by the ACTIVE field in the
cioc0
register (see Table 7 on page 26). The default
value upon reset and powerup is ACTIVE = 0 (i.e.,
inactive). In the inactive mode, the codec clocks are
disabled, data transfers by the codec are disabled, and
analog bias currents are shut off. This state is useful in
battery-powered applications when prolonged periods
of inactivity are expected. It takes approximately
600 ms for the codec to reach full steady-state perfor-
mance in going from inactive to active. This is primarily
due to the charging of the large external capacitors,
C
REF
and C
REG
. However, the codec is functionally
useful after 100 ms.
4.3.2 Input Select
When the A/D preamplifier is selected (EIGS = 0), the
INSEL field of
cioc0
(see Table 7 on page 26) switches
the preamp input between the MICIN and AUXIN
inputs. When external gain select is used (EIGS = 1),
the INSEL field has no effect.
4.3.3 A/D Input Ranges
When the preamplifier is used (EIGS = 0), the IRSEL
field of the
cioc0
register (see Table 7 on page 26)
selects the 500 mVp range when IRSEL = 0 and the
160 mVp range when IRSEL = 1. IRSEL has no effect
when the external gain select mode is used (EIGS = 1).
When EIGS = 1, the inverting amplifier of Figure 5 on
page 7 replaces the preamplifier. The input range in
this mode is the following:
V
FULL-SCALE
=
4.3.4 Output Mute Function
The D/A converter output can be selectively muted with
the MUTE field in the
cioc0
register (see Table 7 on
page 26). The default value upon reset is muted
(MUTE = 0). The mute function is implemented (Figure
3 on page 5) internally by a MUX following the D/A
input. Placing the mute function here causes the signal
at the analog output to gradually decay/rise over
approximately 1 ms upon muting/unmuting. This effect
is due to the impulse response and group delay of the
digital filters. This implementation will reduce any
potentially undesirable transient effects such as pops,
when the D/A is muted.
Rfb
---------
1.578 Vp
×
相關PDF資料 |
PDF描述 |
|---|---|
| CT1469-2 | CT1469-2 MIL-STD-1397 Type E 10MHz Transceiver |
| CT1496-2 | CT1496-2 MIL-STD-1397 Type E 10MHz Low Level Serial Manchester 32 Bit Encoder |
| CT1508-2 | CT1508-2 MIL-STD-1397 Type E 10MHz Serial Manchester 4-Bit SIS / SOS Decoder |
| CT1611 | DMA Controller with Buffer Memory,MIL-STD-1750A Compatible |
| CT1611-FP | DMA Controller with Buffer Memory,MIL-STD-1750A Compatible |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CSP1027J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC |
| CSP1027-J11-DB | 制造商:Alcatel-Lucent 功能描述: |
| CSP1027S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC |
| CSP1027-S11-DB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CSP1034AH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
發布緊急采購，3分鐘左右您將得到回復。