- 您現在的位置：買賣IC網 > PDF目錄16215 > CP2201EK (Silicon Laboratories Inc)KIT EVAL FOR CP2201 ETH CTRLR PDF資料下載
參數資料
| 型號： | CP2201EK |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 96/108頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT EVAL FOR CP2201 ETH CTRLR |
| 標準包裝： | 1 |
| 主要目的： | 接口，以太網傳感器 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | CP2200，CP2201 |
| 主要屬性： | 溫度和光傳感器 |
| 次要屬性： | 圖形用戶界面 |
| 已供物品： | 板，電源，線纜，CD |
| 產品目錄頁面： | 627 (CN2011-ZH PDF) |
| 相關產品： | 336-1313-ND - IC ETH CTRLR SNGL-CHIP 28QFN 336-1312-ND - IC ETH CTRLR SNGL-CHIP 48TQFP |
| 其它名稱： | 336-1316 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁當前第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
CP2200/1
88
Rev. 1.0
15. Physical Layer (PHY)
The CP2200/1 has an IEEE 802.3 compliant 10 BASE-T Ethernet physical layer transceiver that includes a
receiver, transmitter, auto-negotiation, loopback, jabber, smart squelch, polarity correction, and link integrity
functions. If enabled, the auto-negotiation function automatically negotiates the speed of the data link and the
duplex mode. Both half-duplex and full-duplex modes are supported.
The physical layer is controlled and monitored through three registers: PHYCN, PHYCF, and PHYSTA. The various
functions and test modes that can be enabled and monitored through these registers are explained in the following
sections.
15.1. Auto-Negotiation and Duplex Mode
Auto-negotiation allows the CP2200/1 to be connected to any 10/100/1000 BASE-T Ethernet network and
advertise its capabilities. Auto-negotiation uses a series of fast link pulses to send 16-bit link code words. Many
conditions (e.g., failure to detect fast link pulses) can cause auto-negotiation to fail. On failure, the Auto-Negotiation
Failed interrupt will be generated, and/or the Auto-Negotiation Complete Interrupt will not be generated. The
PHYSTA status register will indicate the cause of failure, and the physical layer will default to half-duplex mode. On
success, the Auto-Negotiation Complete interrupt will be generated, and the Auto-Negotiation Failed interrupt will
not be generated. Both interrupts must be checked to ensure that Auto-Negotiation has succeeded.
The advertised link speed will always be 10BASE-T. The duplex mode (half or full) will be negotiated, and full
duplex will be selected if supported by the network. Full duplex mode allows the physical layer to send and receive
data at the same time. In half duplex mode, data can only be transmitted or received at any given time. Full duplex
mode provides overall higher performance and reduces collisions. Software may also choose to advertise its ability
to send and receive PAUSE control packets by setting ADPAUSE (PHYCF.2) to ‘1’.
Important Note: When using auto-negotiation, the auto-negotiation enable bit AUTONEG (PHYCF.4) must
be set to ‘1’ prior to enabling the physical layer. To restart auto-negotiation, the physical layer (transmitter,
receiver, or both) must be disabled and reenabled.
Important Note: The CP220x supports legacy link partners that cannot auto-negotiate. If the link partner cannot
autonegotiate, then the physical layer will default to half-duplex mode.
15.2. Auto-Negotiation Synchronization
The CP220x implements an autonegotiation scheme where autonegotiation is attempted for 250 ms, then a break-
link delay of 1.5 seconds is inserted between auto-negotiation attempts. When the break-link delay is active, the
CP220x does not listen for incoming auto-negotiation requests and does not attempt to auto-negotiate. If one
device starts autonegotiation while the other device is in its “break-link period”, the autonegotiation attempt will fail.
If the devices are unsyncronized, this can lead to a situation where each device attempts to autonegotiate in the
other device’s “break-link period”. This can be solved by synchronizing one or both devices using the following
procedure:
Step 1: Disable the physical layer by writing 0x00 to the PHYCN register.
Step 2: Enable the physical layer with link integrity test and auto-negotiation turned off.
1.Disable the transmitter power save mode (TXPWR = 0x80) and set physical layer options
(PHYCF = SMSQ | JABBER | ADPAUSE | AUTOPOL).
2.Enable the physical layer (PHYEN = 1).
3.Wait for the physical layer to power up. See Physical Layer Startup Time in Table 22 on page 93.
4.Enable the transmitter and receiver (TXEN = 1 and RXEN = 1).
Step 3: Poll the Wake-on-LAN interrupt flag (WAKEINT) to detect if a link partner is present.
1.If there is a signal, wait 250 ms then begin autonegotiation.
2.If there is no signal, wait 1.5 seconds then begin autonegotiation.
相關PDF資料 |
PDF描述 |
|---|---|
| PM1210-820J-RC | INDUCTOR 82UH 5% 1210 SMD |
| H3WWH-6036G | IDC CABLE - HPL60H/AE60G/HPL60H |
| UPS2C471MRD | CAP ALUM 470UF 160V 20% RADIAL |
| A3CKB-4006M | IDC CABLE - AKC40B/AE40M/APK40B |
| MODEMDK | KIT DEV EMBEDDED MODEM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP2201-GM | 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| CP2201-GMR | 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| CP-220-K | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Coils and Chokes for general use |
| CP221 | 制造商:CENTRAL 制造商全稱:Central Semiconductor Corp 功能描述:Small Signal Transistor |
| CP-221 1 1/2"BL 100' | 功能描述:HEATSHRNK CP221 1-1/2" X 100'BLK 制造商:3m 系列:CP-221 零件狀態:過期 類型:套管，彈性 收縮率:2 至 1 長度:100'（30.48m） 內徑（出廠）:1.500"（38.1mm） 內徑 - 恢復后:0.752"（19.1mm） 恢復后的壁厚:0.040"（1.02mm） 材料:聚烯烴（PO） 特性:自熄滅 顏色:黑 工作溫度:-55°C ~ 135°C 收縮溫度:121°C 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。